G'day, alienjeff, no I didn't try any of the Beta's. SirDuncan, Once it has been loaded to a hard drive then it doesn't seem to matter whether it is a Frugal or a Full install. I have two partitions (on separate physical drives) and have tried upgrading an older version (2.14), frugal install, and f...

G'day, Update to previous post: Everything works when booting from CD, pfix=ram,clean but ethernet is not detected when running from HD and USB does not exist in any form. The ethernet drivers "forcedeath" and "3c59x" which load from cd will NOT load, even when manually selected,...

G'day, I like the 3.00 release except for three things. 1. It doesn't detect eth0 or eth1 on one computer (Desktop with asus m/board) or eth0 on the other (Gateway laptop) or load the modules (or drivers or whatever they are in the wizard for network). These worked fine previoulsy (2.14). 2. My USB ...

G'day,

Thanks for the ideas. I got gyachi working. I also had to use Muppy Webcam for some reason. If I open MuppyWebcam to get the camera working, close it, then open gyachi, it seems to be all working.

Thanks again to all who put the work into these things, it is greatly appreciated.

G'day,

I have found out that it doesn't do it. My bad. I thought that it did. Is there a chat programme that does support webcam sending and recieving?

G'day,

I'm curious. Are you a vegetarian because you love animals or because you hate plants?

G'day,

I have Pidgin working successfully. I also have my webcam (Logitech) working Muppy Webcam. However, I can't seem to get the webcam working with Pidgin. I get what looks like a greyed-out TV icon, as seen below next to the smilies. What must I do?

G'day, :D I have it working. It took a bit of messing around, moving some things and renaming some stuff but with all your help we got there. :D Thank you muchly. The method I use to connect and be able to transfer files is to open a console and type 'PocketPCwizard' and start the connection, then o...

G'day, Once again thanks, but still no joy. I have Puppy installed to my hard drive so I put the sfs file in / but it doesn't seem to do anything at all. I rebooted with no benefit. I don't put devx type files anywhere. I assume that they are put where they are supposed to be by whoever put them whe...

G'day, Thanks John Doe for your quick response. I have downloaded everything from the link I could but still cannot connect to my PDA. I am not sure where to put the mobi_214.sfs file, or what to do with it when it gets there. I have no idea where my save session is. It will be wherever it is suppos...

G'day, I have an HP iPAQ PDA (Windows Mobile 2003 SE Version 4.21.1088) which connects to my computer via a cradle to USB. I am running PuppyLinux 2.16 on the computer and have been running all the releases for a few years. I have never had any luck getting Puppy to see the PDA, let alone synchroniz...

G'day,

Thanks klhrevolutionist but it didn't work. It still stops at the same place.

G'day,

Thank sunburnt. I can run Puppy from the CD but where would I find the SAVE file so that I can rename it? I assume that it is in the same partition that Puppy normally runs from (in my case /mnt/hda5)

G'day, Whenever the power goes out (or circuit-breaker breaks) and the computer is consequently turned off, PuppyLinux doesn't boot up completely. It gets to the line which says personal config script /etc/rc.d/rc.local. . . done (I can't read the first part of the line because it is set too far to ...

G'day again, I now have managed to get WINE installed (I think). The Configuration is working anyway. I cannot seem to get anything working in it. I do have some Windoze partitions, with XP and 2000. I have tried linking to programmes on these partitions (mounted) and also unzipping a Windoze applic...

G'day again, I went to the link, downloaded the 2 files mentioned http://dotpups.de/dotpups/Emulators/Wine-0.9.22/Wine-0.9.22-drive_c-and-Wordview.pup http://dotpups.de/dotpups/Emulators/Wine-0.9.22/Wine-mime-type-for-Rox-1.2.pup Now when I click winecfg in /usr.local/Wine-mime-type-for-Rox-1.2 I ge...

G'day, I just downloaded the Slackware version from winehq.com, saved it to /, extracted all, and went to /usr/bin and clicked on winebuild. It flashed (or maybe "winked" would be a better term) at me a couple of times then did nothing. If i tried doing it using a console it came up with a...

G'day,

Sorry, I got the wrong terminology, but you figured it out. Thanks again for your work.

G'day,

I like your programme. I have a suggestion though. Can it be made to rip a file which is on the hard drive rather than a cd? It may be possible now but I couldn't find a way to do it as it kept looking for a cd.

Thanks for your work, it is appreciated.

G'day,

Thanks for the quick response. I downloaded XnView and it will do what I need it to do. Muchly appreciated.