Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Fri 01 Aug 2014, 11:59
All times are UTC - 4
 Forum index » Advanced Topics » Hardware » Video
DRI Module Load Problem
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 1 [10 Posts]  
Author Message
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Sat 29 Sep 2007, 14:40    Post subject:  DRI Module Load Problem
Subject description: bootsysinit.log reports error
 

Hello,
I've loaded the 3D Control Center and installed the DRI drivers. But I get the following in bootsysinit.log (see the "loading x dri modules" error below):

Mounting devpts: Mounting /sys: Starting /etc/rc.d/rc.modules...
loading modules for core usb...
loading modules for pci interfaces...
loading module via-agp

loading module via-ircc

loading module snd-via82xx

loading module via-rhine

loading modules for pcmcia...
loading x dri modules...
Usage: modprobe.bin [-v] [-V] [-C config-file] [-n] [-i] [-q] [-b] [-o <modname>] <modname> [parameters...]
modprobe.bin -r [-n] [-i] [-v] <modulename> ...
modprobe.bin -l -t <dirname> [ -a <modulename> ...]

Appreciate any help.
Thanks,
Martin
Back to top
View user's profile Send private message 
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Sat 29 Sep 2007, 15:07    Post subject:  

Along with the above condition suddenly I have no Xorg.0.log generated(?). Does this make sense? The display seems to launch Xvesa as a default but I don't have any record of the xserver load. Any ideas?
Thanks,
Martin
Back to top
View user's profile Send private message 
tempestuous

Joined: 10 Jun 2005
Posts: 5218
Location: Australia

PostPosted: Sun 30 Sep 2007, 00:09    Post subject:  

More information please:
- graphics card
- Puppy version
Back to top
View user's profile Send private message 
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Mon 01 Oct 2007, 18:18    Post subject:  

Graphics card is Via CLE266 (part of their EPIA ME6000G mboard). Puppy version is 2.17. Thanks tempestuous...
Martin
Back to top
View user's profile Send private message 
tempestuous

Joined: 10 Jun 2005
Posts: 5218
Location: Australia

PostPosted: Mon 01 Oct 2007, 22:38    Post subject:  

It sounds like you are running Xvesa?
To first make sure Xorg is running, exit X with <Control><Alt><Backspace> then type "xorgwizard", then "Enter".

Then run 3DCC again.
Back to top
View user's profile Send private message 
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Tue 02 Oct 2007, 12:52    Post subject:  

Yes, I'm currently limited to running Xvesa. I did run the xorgwizard and was able have it create the xorg.0.log. I'll post the output warnings, etc. later today.
Thanks.
Back to top
View user's profile Send private message 
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Fri 05 Oct 2007, 00:23    Post subject:  

Here's the relevant xorg.conf:

Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the font modules
Load "type1"
Load "freetype"

# This loads the GLX module
Load "glx"

# This loads xtrap extension, used by xrandr
Load "xtrap"

Load "dri"

EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 30-61
VertRefresh 56-76
#UseModes "Modes0" #monitor0usemodes
EndSection

Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection

Section "Device"
Identifier "Card0"
Driver "via" #card0driver
VendorName "Unknown Vendor"
BoardName "Unknown Board"
BusID "PCI:1:0:0"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
Subsection "Display"
Depth 16
Modes "1024x768"
EndSubsection
EndSection

Section "DRI"
Mode 0666
EndSection

And here's the associated xorg.0.log
_XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6
_XSERVTransOpen: transport open failed for inet6/puppypc:0
_XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6

X Window System Version 7.0.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 7.0
Build Operating System:Linux 2.6.18-inside-sandbox i386
Current Operating System: Linux puppypc 2.6.21.5 #1 Sat Jun 23 21:16:21 PUP 2007 i686
Build Date: 08 August 2006
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Oct 4 21:04:10 2007
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) FontPath set to "/usr/X11R7/lib/X11/fonts/misc/,/usr/X11R7/lib/X11/fonts/Type1/,/usr/X11R7/lib/X11/fonts/TTF/"
(**) RgbPath set to "/usr/X11R7/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R7/lib/xorg/modules"
(**) Option "RandR" "on"
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.8
X.Org XInput driver : 0.5
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R7/lib/xorg/modules/fonts/libbitmap.so
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R7/lib/xorg/modules/libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(--) using VT number 3

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,3123 card 1106,aa01 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,b091 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:0d:0: chip 1106,3044 card 1106,3044 rev 80 class 0c,00,10 hdr 00
(II) PCI: 00:10:0: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:1: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:2: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:3: chip 1106,3104 card 1106,3104 rev 82 class 0c,03,20 hdr 00
(II) PCI: 00:11:0: chip 1106,3177 card 1106,aa01 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:11:1: chip 1106,0571 card 1106,aa01 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:11:5: chip 1106,3059 card 1106,aa01 rev 50 class 04,01,00 hdr 00
(II) PCI: 00:12:0: chip 1106,3065 card 1106,0102 rev 74 class 02,00,00 hdr 00
(II) PCI: 01:00:0: chip 1106,3122 card 1106,3122 rev 03 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xdc000000 - 0xddffffff (0x2000000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:17:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) unknown vendor (0x1106) unknown chipset (0x3122) rev 3, Mem @ 0xd8000000/26, 0xdc000000/24
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xd0000000 from 0xd7ffffff to 0xcfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xde002000 - 0xde0020ff (0x100) MX[B]
[1] -1 0 0xde001000 - 0xde0010ff (0x100) MX[B]
[2] -1 0 0xde000000 - 0xde0007ff (0x800) MX[B]
[3] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[4] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[5] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[6] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[7] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[8] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[9] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[10] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[11] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[12] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xde002000 - 0xde0020ff (0x100) MX[B]
[1] -1 0 0xde001000 - 0xde0010ff (0x100) MX[B]
[2] -1 0 0xde000000 - 0xde0007ff (0x800) MX[B]
[3] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[4] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[5] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[6] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[7] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[8] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[9] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[10] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[11] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[12] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xde002000 - 0xde0020ff (0x100) MX[B]
[6] -1 0 0xde001000 - 0xde0010ff (0x100) MX[B]
[7] -1 0 0xde000000 - 0xde0007ff (0x800) MX[B]
[8] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[9] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[10] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[14] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[15] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[16] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[17] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[18] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[19] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/X11R7/lib/xorg/modules/fonts/libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) LoadModule: "freetype"
(II) Loading /usr/X11R7/lib/xorg/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 7.0.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions/libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "xtrap"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions/libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DEC-XTRAP
(II) LoadModule: "via"
(II) Loading /usr/X11R7/lib/xorg/modules/drivers/via_drv.so
(II) Module via: vendor="X.Org Foundation"
compiled for 4.3.99.902, module version = 0.1.33
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.8
(II) LoadModule: "mouse"
(II) Loading /usr/X11R7/lib/xorg/modules/input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.4
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) LoadModule: "kbd"
(II) Loading /usr/X11R7/lib/xorg/modules/input/kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) VIA: driver for VIA chipsets: CLE266, KM400/KN400, K8M800,
PM800/PM880/CN400
(II) Primary Device is: PCI 01:00:0
(--) Chipset CLE266 found
(!!) VIA Technologies does not support or endorse this driver in any way.
(!!) For support please contact the driver maintainer or your X vendor.
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xde002000 - 0xde0020ff (0x100) MX[B]
[6] -1 0 0xde001000 - 0xde0010ff (0x100) MX[B]
[7] -1 0 0xde000000 - 0xde0007ff (0x800) MX[B]
[8] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[9] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[10] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[14] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[15] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[16] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[17] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[18] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[19] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xde002000 - 0xde0020ff (0x100) MX[B]
[6] -1 0 0xde001000 - 0xde0010ff (0x100) MX[B]
[7] -1 0 0xde000000 - 0xde0007ff (0x800) MX[B]
[8] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[9] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[10] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[11] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[12] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[13] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[16] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[17] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[18] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[19] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[20] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[21] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[22] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
[23] 0 0 0xdd0003b0 - 0xdd0003bb (0xc) IS[B]
[24] 0 0 0xdd0003c0 - 0xdd0003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R7/lib/xorg/modules/libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.8
(**) VIA(0): Depth 16, (--) framebuffer bpp 16
(==) VIA(0): RGB weight 565
(==) VIA(0): Default visual is TrueColor
(==) VIA(0): Using HW cursor
(--) VIA(0): Chipset: "CLE266"
(--) VIA(0): mapping MMIO @ 0xdc000000 with size 0x9000
(--) VIA(0): mapping BitBlt MMIO @ 0xdc200000 with size 0x10000
(II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(--) VIA(0): Chipset Rev.: 18
(WW) VIA(0): Manufacturer plainly copied main PCI ids to Subsystem/Card ids.
(--) VIA(0): Detected VIA EPIA M/MII/....
(==) VIA(0): Using gamma correction (1.0, 1.0, 1.0)
(--) VIA(0): videoram = 32768k
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R7/lib/xorg/modules/libi2c.so
(II) Module i2c: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.8
(II) VIA(0): I2C bus "I2C bus 1" initialized.
(II) VIA(0): I2C bus "I2C bus 2" initialized.
(II) VIA(0): I2C bus "I2C bus 3" initialized.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R7/lib/xorg/modules/libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(II) VIA(0): I2C device "I2C bus 1:ddc2" registered at address 0xA0.
(II) VIA(0): I2C device "I2C bus 1:ddc2" removed.
(II) VIA(0): Manufacturer: PHL Model: 804 Serial#: 70779920
(II) VIA(0): Year: 2002 Week: 15
(II) VIA(0): EDID Version: 1.3
(II) VIA(0): Analog Display Input, Input Voltage Level: 0.714/0.286 V
(II) VIA(0): Sync: Separate Composite SyncOnGreen
(II) VIA(0): Max H-Image Size [cm]: horiz.: 30 vert.: 22
(II) VIA(0): Gamma: 2.20
(II) VIA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) VIA(0): First detailed timing is preferred mode
(II) VIA(0): redX: 0.597 redY: 0.343 greenX: 0.316 greenY: 0.566
(II) VIA(0): blueX: 0.153 blueY: 0.131 whiteX: 0.310 whiteY: 0.328
(II) VIA(0): Supported VESA Video Modes:
(II) VIA(0): 720x400@70Hz
(II) VIA(0): 640x480@60Hz
(II) VIA(0): 640x480@67Hz
(II) VIA(0): 640x480@72Hz
(II) VIA(0): 640x480@75Hz
(II) VIA(0): 800x600@56Hz
(II) VIA(0): 800x600@60Hz
(II) VIA(0): 800x600@72Hz
(II) VIA(0): 800x600@75Hz
(II) VIA(0): 832x624@75Hz
(II) VIA(0): 1024x768@60Hz
(II) VIA(0): 1024x768@70Hz
(II) VIA(0): 1024x768@75Hz
(II) VIA(0): Manufacturer's mask: 0
(II) VIA(0): Supported additional Video Mode:
(II) VIA(0): clock: 65.0 MHz Image Size: 304 x 228 mm
(II) VIA(0): h_active: 1024 h_sync: 1048 h_sync_end 1184 h_blank_end 1344 h_border: 0
(II) VIA(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 806 v_border: 0
(II) VIA(0): Serial No: BZ 70779920
(II) VIA(0): Monitor name: Philips 150B
(II) VIA(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 61 kHz, PixClock max 80 MHz
(II) VIA(0): I2C device "I2C bus 2:VT162x" registered at address 0x40.
(--) VIA(0): Detected VIA Technologies VT1622 TV Encoder
(--) VIA(0): VT162x: Nothing connected.
(II) VIA(0): Monitor0: Using hsync range of 30.00-61.00 kHz
(II) VIA(0): Monitor0: Using vrefresh range of 56.00-76.00 Hz
(II) VIA(0): Clock range: 20.00 to 230.00 MHz
(II) VIA(0): Not using default mode "640x350" (vrefresh out of range)
(II) VIA(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "640x400" (vrefresh out of range)
(II) VIA(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "720x400" (vrefresh out of range)
(II) VIA(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "640x480" (vrefresh out of range)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "800x600" (vrefresh out of range)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (interlace mode not supported)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(WW) (1024x768,Monitor0) mode clock 94.5MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1024x768" (hsync out of range)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(WW) (1152x864,Monitor0) mode clock 108MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1152x864" (hsync out of range)
(II) VIA(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(WW) (1280x960,Monitor0) mode clock 108MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(WW) (1280x960,Monitor0) mode clock 148.5MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1280x960" (hsync out of range)
(II) VIA(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(WW) (1280x1024,Monitor0) mode clock 108MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1280x1024" (hsync out of range)
(II) VIA(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1280x1024,Monitor0) mode clock 135MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1280x1024" (hsync out of range)
(II) VIA(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1280x1024,Monitor0) mode clock 157.5MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1280x1024" (hsync out of range)
(II) VIA(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor0) mode clock 162MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor0) mode clock 175.5MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor0) mode clock 189MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor0) mode clock 202.5MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor0) mode clock 229.5MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1792x1344,Monitor0) mode clock 204.8MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1792x1344" (hsync out of range)
(II) VIA(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(WW) (1856x1392,Monitor0) mode clock 218.3MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1856x1392" (hsync out of range)
(II) VIA(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1152x768" (vrefresh out of range)
(II) VIA(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan)
(WW) (1400x1050,Monitor0) mode clock 122MHz exceeds DDC maximum 80MHz
(II) VIA(0): Not using default mode "1400x1050" (hsync out of range)
(II) VIA(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VIA(0): CrtcHSyncEnd out of range.
(II) VIA(0): Not using default mode "1400x1050" (horizontal sync too wide)
(II) VIA(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1600x1024" (no clock available for mode)
(II) VIA(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1280x960" (width too large for virtual size)
(--) VIA(0): Virtual size is 1024x768 (pitch 1024)
(**) VIA(0): *Default mode "1024x768": 78.8 MHz (scaled from -299.7 MHz), 60.1 kHz, 75.1 Hz
(II) VIA(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
(**) VIA(0): Default mode "1024x768": 75.0 MHz (scaled from -440.1 MHz), 56.5 kHz, 70.1 Hz
(II) VIA(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
(**) VIA(0): Default mode "1024x768": 65.0 MHz (scaled from 796.0 MHz), 48.4 kHz, 60.0 Hz
(II) VIA(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
(**) VIA(0): Default mode "832x624": 57.3 MHz (scaled from 799.9 MHz), 49.7 kHz, 74.6 Hz
(II) VIA(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync
(**) VIA(0): Default mode "800x600": 49.5 MHz (scaled from -579.5 MHz), 46.9 kHz, 75.0 Hz
(II) VIA(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
(**) VIA(0): Default mode "800x600": 50.0 MHz (scaled from 241.8 MHz), 48.1 kHz, 72.2 Hz
(II) VIA(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
(**) VIA(0): Default mode "800x600": 40.0 MHz (scaled from -127.7 MHz), 37.9 kHz, 60.3 Hz
(II) VIA(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
(**) VIA(0): Default mode "800x600": 36.0 MHz (scaled from -275.5 MHz), 35.2 kHz, 56.2 Hz
(II) VIA(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
(**) VIA(0): Default mode "640x480": 31.5 MHz (scaled from 361.1 MHz), 37.5 kHz, 75.0 Hz
(II) VIA(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
(**) VIA(0): Default mode "640x480": 31.5 MHz (scaled from 361.1 MHz), 37.9 kHz, 72.8 Hz
(II) VIA(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync
(**) VIA(0): Default mode "640x480": 25.2 MHz (scaled from -674.5 MHz), 31.5 kHz, 60.0 Hz
(II) VIA(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
(--) VIA(0): Display dimensions: (300, 220) mm
(--) VIA(0): DPI set to (86, 8Cool
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R7/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R7/lib/xorg/modules/libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.8
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R7/lib/xorg/modules/libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 7.0.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.8
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xdc000000 - 0xdcffffff (0x1000000) MS[B]
[1] 0 0 0xd8000000 - 0xdbffffff (0x4000000) MS[B]
[2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xde002000 - 0xde0020ff (0x100) MX[B]
[8] -1 0 0xde001000 - 0xde0010ff (0x100) MX[B]
[9] -1 0 0xde000000 - 0xde0007ff (0x800) MX[B]
[10] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[11] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[12] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[19] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[20] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[21] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[22] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[23] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[24] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
[25] 0 0 0xdd0003b0 - 0xdd0003bb (0xc) IS[B]
[26] 0 0 0xdd0003c0 - 0xdd0003df (0x20) IS[B]
(--) VIA(0): mapping framebuffer @ 0xd8000000 with size 0x2000000
(==) VIA(0): Write-combining range (0xd8000000,0x2000000)
(--) VIA(0): Frame buffer start: 0xb5909000, free start: 0x180000 end: 0x2000000
(--) VIA(0): mapping MMIO @ 0xdc000000 with size 0x9000
(--) VIA(0): mapping BitBlt MMIO @ 0xdc200000 with size 0x10000
(II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) VIA(0): 3D Engine has been initialized.
(II) VIA(0): VIAInternalScreenInit
(II) VIA(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
8x8 color pattern filled rectangles
Solid Lines
Dashed Lines
Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
10 256x256 slots
32 8x8 color pattern slots
(==) VIA(0): Backing store disabled
(II) VIA(0): direct rendering disabled
(II) VIA(0): Benchmarking video copy. Less is better.
(--) VIA(0): Timed libc YUV420 copy... 4570186. Throughput: 77.9 MiB/s.
(--) VIA(0): Timed kernel YUV420 copy... 4547379. Throughput: 78.3 MiB/s.
(--) VIA(0): Ditch SSE YUV420 copy... Not supported by CPU.
(--) VIA(0): Timed MMX YUV420 copy... 3074278. Throughput: 115.8 MiB/s.
(--) VIA(0): Timed 3DNow! YUV420 copy... 3078852. Throughput: 115.6 MiB/s.
(--) VIA(0): Ditch MMX2 YUV420 copy... Not supported by CPU.
(--) VIA(0): Using MMX YUV42X copy for video.
(WW) VIA(0): [XvMC] Cannot use XvMC without DRI!
(**) RandR enabled
(II) Setting vga for screen 0.
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(**) Option "Protocol" "auto"
(**) Mouse0: Device: "/dev/mouse"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/mouse"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 9
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc102"
(**) Keyboard0: XkbModel: "pc102"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
FreeFontPath: FPE "/usr/X11R7/lib/X11/fonts/misc/" refcount is 2, should be 1; fixing.
(--) VIA(0): mapping framebuffer @ 0xd8000000 with size 0x2000000
(==) VIA(0): Write-combining range (0xd8000000,0x2000000)
(--) VIA(0): Frame buffer start: 0xb5909000, free start: 0x180000 end: 0x2000000
(--) VIA(0): mapping MMIO @ 0xdc000000 with size 0x9000
(--) VIA(0): mapping BitBlt MMIO @ 0xdc200000 with size 0x10000
(II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) VIA(0): VIAInternalScreenInit
(II) VIA(0): direct rendering disabled
(WW) VIA(0): [XvMC] Cannot use XvMC without DRI!
(**) RandR enabled
(II) Mouse0: ps2EnableDataReporting: succeeded
FreeFontPath: FPE "/usr/X11R7/lib/X11/fonts/misc/" refcount is 2, should be 1; fixing.

Thanks for any pointers.
/Martin
Back to top
View user's profile Send private message 
tempestuous

Joined: 10 Jun 2005
Posts: 5218
Location: Australia

PostPosted: Fri 05 Oct 2007, 20:14    Post subject:  

The via DRI (3D) driver has a quirk in that Xorg.0.log does not report whether it's running.
You need to run "glxinfo" and "xdriinfo"
I think these are installed as part of the 3D control centre (?). Try
Code:
/usr/local/3DCC/resource/glxinfo

and
Code:
/usr/local/3DCC/resource/xdriinfo


If these utilities are not available, they can be installed as part of the glxgears-pup1x.pup from
http://www.murga-linux.com/puppy/viewtopic.php?p=80828#80828

You want to see something like "direct rendering: Yes"

Regarding the XvMC error in your Xorg.0.log, pakt reports that XvMC can be enabled by adding this text under Section "Module" of your xorg.conf -
Code:
Subsection "extmod"
    Option "omit xfree86-dga"
EndSubsection

But XvMC is only useful for DVD (MPEG2) video playback. It won't make any difference to 3D performance.
Back to top
View user's profile Send private message 
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Thu 11 Oct 2007, 01:19    Post subject:  

Thanks for the pointers, Tempestuous. I apologize for the delay but I got pulled in other directions over the past week. The good news is I've got puppy recognizing my internal 802.11g card. If I can just get this Xorg/CLE266 issue resolved, I'll have the system I've been hoping for. I need to step back and reinstall the 3dcc over the next day or two. I'll post results of your suggested glx and xdriinfo utilities.
/Martin
Back to top
View user's profile Send private message 
pupquest

Joined: 07 Sep 2007
Posts: 19

PostPosted: Mon 22 Oct 2007, 00:20    Post subject:  

Just to close up this issue... I installed Puppy 3.01 and my CLE266 chip is now automatically recognized and configured correctly by the xorgwizard. Excellent! Thanks for all your help.
/Martin
Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 1 of 1 [10 Posts]  
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » Advanced Topics » Hardware » Video
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.1631s ][ Queries: 12 (0.0064s) ][ GZIP on ]