[obsolete] Compiz-Fusion Puplet for testing -- aka "W...

A home for all kinds of Puppy related projects
Message
Author
User avatar
cb88
Posts: 1165
Joined: Mon 29 Jan 2007, 03:12
Location: USA
Contact:

#41 Post by cb88 »

Taking Puppy Linux to the limit of perfection. meanwhile try "puppy pfix=duct_tape" kernel parem eater.
X86: Sager NP6110 3630QM 16GB ram, Tyan Thunder 2 2x 300Mhz
Sun: SS2 , LX , SS5 , SS10 , SS20 ,Ultra 1, Ultra 10 , T2000
Mac: Platinum Plus, SE/30

The Jinx
Posts: 24
Joined: Fri 14 Sep 2007, 13:55
Location: Brooklyn, New York

#42 Post by The Jinx »

hey would those links cb88 recommend work with ati xpress 200 (desktop version) or is it strictly for the mobile version of ati xpress 200

User avatar
SirDuncan
Posts: 829
Joined: Sat 09 Dec 2006, 20:35
Location: Ohio, USA
Contact:

#43 Post by SirDuncan »

I honestly don't know if there is any major difference between the regular and the mobile versions of the cards in terms of setup. I suggest you create a new save file (or boot from CD if you have a full HD install) and try it on the clean file so that you don't mess up anything important if it doesn't work.
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath

User avatar
tombh
Posts: 422
Joined: Fri 12 Jan 2007, 12:27
Location: Bristol, UK
Contact:

#44 Post by tombh »

So just to be clear -- For The Jinx and Caneri 3D acceleration and thus wNOP will only work for you once the fglrx driver is properly installed, that needs to be the first thing to happen.

Also just to be clear about installing this driver:
(1) You will need to be in wNOP to run it.
(2) devx_301.sfs must be installed on wNOP
(2)(a) This can be done by booting wNOP with a savefile, then placing devx301.sfs in /mnt/home. If devx_301 doesn't mount on subsequent boots then use Xfce Menu -> Puppy Setup -> Bootmanager to make sure it does. To test if devx_301 is installed typing

Code: Select all

gcc
at the terminal should return the output:

Code: Select all

gcc: no input files
(3)The command:

Code: Select all

aticonfig --initial
needs to be run from the terminal after successful driver installation.
(4) Reboot needed

(Don't worry all this will be in wNOP2!)

SirDuncan
Thanks for those dump files. Interestingly the radeon driver dump appears to be perfect! DRI is active and xorg.conf reports no errors. The only clue I can see is that the module "intel_agp" is being loaded, no doubt because of a legacy intel graphics card which I assume you have disabled through the BIOS or whatever. Strictly that module shouldn't be loaded, but I'm not sure how to stop it, but then I'm not totally sure it's the cause of the problem. What I really need to see now is the output of

Code: Select all

compiz-manager
from within that first fresh (ie pfix=ram) boot of wNOP.

As for the fglrx dump file, xorg.conf has not been setup, so maybe you didn't run "aticonfig --initial" after installation. Also did you follow most of the steps outlined above? And would it be possible to run the installer from the terminal to catch any of its output -- I know its got a horrible long name but something I only just learnt recently is that if you type the first few letters of a command and then press tab twice bash autocompletes with suggestions!

Thanks :) And no rush.

Okay I can wait for Kiba, it looks fantastic though. If I get desperate I'll go a-hunting in the Ubuntu forests :)

P.S. Seeing as it looks like the fglrx driver will be an added feature and so added MBs to wNOP2, it would be great to try and compile the Compiz-Config-Settings-Manager into a standalone executable. I reckon that could cut a fair amount of MBs away from the final ISO size. If anybody has any python experience I've been looking at PyInstaller to do the job.

An ode to the wobble
Upon the shoulders of our forebears,
Barry, gray and wow to name but some,
Through rain, snow and ripple effects --
We shall strive to conquer fusion.

So that every corner may be activated
And as if from the highest summit
We may see the truest vista --
all windows in a single desktop fit :)

User avatar
SirDuncan
Posts: 829
Joined: Sat 09 Dec 2006, 20:35
Location: Ohio, USA
Contact:

#45 Post by SirDuncan »

Somehow I was afraid that the old Intel card might be a problem. I would have removed it if it weren't built in to the motherboard. I'll have to see what I can do to stop it from loading.

I did run "aticonfig" although I used the command "aticonfig --initial --something_else_I_don't_remember_but_was_told_to_do_in_a_how-to_I_found". Perhaps I shall try just "aticonfig --initial" next time.

Most of what I'm trying to do with Kiba right now is to weed out the unnecessary packages. The Ubuntu repo had it split into a lot of seperate packages. I have it narrowed down to 3-4 right now. That might be good enough to post it for testing. I'll do that when I get home, I have my last final for the quarter in about half an hour. Then I get to go home for winter break.

I already have my desktop packed to leave, so I won't get to do any testing until late tonight (probably early morning tomorrow for you) or tomorrow. I'll be spending most of today driving.
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath

User avatar
cb88
Posts: 1165
Joined: Mon 29 Jan 2007, 03:12
Location: USA
Contact:

#46 Post by cb88 »

sirduncan: If you have screen1 display1 or card1 are in your xorg.conf delete those lines

you should only have screen0 display0 and card0

and try deleting anything that pertains to the intel gpu

that is how I got the nvida 6200 with integrated intel gpu to work
Taking Puppy Linux to the limit of perfection. meanwhile try "puppy pfix=duct_tape" kernel parem eater.
X86: Sager NP6110 3630QM 16GB ram, Tyan Thunder 2 2x 300Mhz
Sun: SS2 , LX , SS5 , SS10 , SS20 ,Ultra 1, Ultra 10 , T2000
Mac: Platinum Plus, SE/30

User avatar
cb88
Posts: 1165
Joined: Mon 29 Jan 2007, 03:12
Location: USA
Contact:

#47 Post by cb88 »

svn downloaded for kiba here you go!

no i don't have svn in puppy ..... downloaded with Xpee..at school
Attachments
akamaru.zip
(13.48 KiB) Downloaded 505 times
kiba-ephy-extension.zip
(27.57 KiB) Downloaded 502 times
kiba-gaim-plugin.zip
(36.97 KiB) Downloaded 491 times
Taking Puppy Linux to the limit of perfection. meanwhile try "puppy pfix=duct_tape" kernel parem eater.
X86: Sager NP6110 3630QM 16GB ram, Tyan Thunder 2 2x 300Mhz
Sun: SS2 , LX , SS5 , SS10 , SS20 ,Ultra 1, Ultra 10 , T2000
Mac: Platinum Plus, SE/30

User avatar
SirDuncan
Posts: 829
Joined: Sat 09 Dec 2006, 20:35
Location: Ohio, USA
Contact:

#48 Post by SirDuncan »

I get home and the first thing I go to do is upload Kiba, only to find that CB has beat me to it. Since he posted the source, I suppose I can still post the binaries (though I will probably recompile now that I have access to source to ensure full Puppy compatibility).

These were plucked from an Ubuntu repository. All 4 are necessary (well, you could leave out the settings manager, but I don't suggest it) and are only tested on wNOP. They should work with any 3.01 (possibly older versions as well) that has Compiz Fusion.

Now, back to work getting wNOP functional on my 9550.
Attachments
libakamaru0-0.1.pet
The Akamaru physics engine (yes this is required)
(7.21 KiB) Downloaded 559 times
kibasettings-0.1.pet
The control panel for Kiba
(32.93 KiB) Downloaded 537 times
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath

User avatar
Lobster
Official Crustacean
Posts: 15522
Joined: Wed 04 May 2005, 06:06
Location: Paradox Realm
Contact:

#49 Post by Lobster »

An ode to the wobble
Upon the shoulders of our forebears,
Barry, gray and wow to name but some,
Through rain, snow and ripple effects --
We shall strive to conquer fusion.

So that every corner may be activated
And as if from the highest summit
We may see the truest vista --
all windows in a single desktop fit Smile
:)

Set
to wobble
Phases on
Stun
Fusion enthuses us to jell
Puppy Raspup 8.2Final 8)
Puppy Links Page http://www.smokey01.com/bruceb/puppy.html :D

azieser
Posts: 7
Joined: Wed 14 Nov 2007, 18:12

Nvidia GeForce 7300 GS up and running

#50 Post by azieser »

Great Job this is running off of a memory stick and is working great. Also the sound module configured itself perfectly, normally I have to work on it to get it up and running.

User avatar
tombh
Posts: 422
Joined: Fri 12 Jan 2007, 12:27
Location: Bristol, UK
Contact:

#51 Post by tombh »

!!!The Kernel Source SFS is also needed to use the ATI installer!!!

However if you don't wnat to use the installer here is a [temporarily unavailable dotpet] for the ATI fglrx v8.42.3 driver. I must point out that I do not have an ATI card supported by this driver, so I cannot say that it works. Also, it will only work with Puppy 3 or Xorg7.1 and later.

In order to make this dotpet I used the "--bldpckg Slackware/All" option when running the original installer. With the thus outputted packages I adjusted the directory for Puppy's xorg library (ie: usr/lib -> /usr/X11R7/lib/xorg), updated the symlinks and made the dotpet. I did test it on my system and /var/log/Xorg.0.log reported the 'correct error' of something like "unsupproted device", therefore everything went alright up to the point of the driver actually trying to talk to my Mobility Radeon 9000.

If anyone has an ATI card more recent than the 9500 series and is willing to try this dotpet out that would be great. You will need to:
(1) Boot into Puppy 3 (any version -- the original, NOP 3.01 or wNOP using <plain Xfce> option) in preparation that EVERYTHING is going to go wrong! Therefore, better make it a pfix=ram session
(2) install the dotpet
(3) upon completion type:

Code: Select all

aticonfig --initial
into a terminal
(4)restart X (CTRL+ALT+BACKSPACE then type xwin to return)

All we're looking for at the moment is that after step (4) you see a desktop and some icons, we can worry about Wobbilyness later.

Good Luck!

PS Thanks azieser
Last edited by tombh on Fri 23 Nov 2007, 23:37, edited 1 time in total.

Caneri
Posts: 1513
Joined: Tue 04 Sep 2007, 13:23
Location: Canada

#52 Post by Caneri »

Well I survived the ati.pet.

I had to make a pup_save file as the first attempt failed and broke xorg...xwin command didn't work when restarted XFCE.

After a pup_save file was created on a spare usb flash I had the ati.pet installed with a warning about a missing a dependency (I forgot to write it down..sheesh). With restarted X the desktop was there.

After a full shutdown/reboot the desktop was there with ati.pet installed.

Tested on an ATI Mobility Radeon X1600/256mb ram (M56 71C5)
[color=darkred][i]Be not afraid to grow slowly, only be afraid of standing still.[/i]
Chinese Proverb[/color]

The Jinx
Posts: 24
Joined: Fri 14 Sep 2007, 13:55
Location: Brooklyn, New York

#53 Post by The Jinx »

I would love to help in testing, but i have no idea what steps i should take. I understand I am suppose to install the dotpet, but what do i do with the kernel Source SFS. Do i still follow the instructions to install the devs_301.sfs a couple of post earlier.

In addition, while i am on wNOP i notice that i cannot sign on to this forum(something about SQL problems) and i and having problems playing movies.(all i see is lines of color) could this have anything to do with me choosing xorg with Generic Drivers.

~ The Jinx

User avatar
cb88
Posts: 1165
Joined: Mon 29 Jan 2007, 03:12
Location: USA
Contact:

#54 Post by cb88 »

I can run compiz in PCLinux OS with this xorg.conf will atempt to copy to puppy right now..... the chip is an integrated intel ‎865 Chipset Graphics Controller

Code: Select all

Identification
Vendor: ‎Intel Corp.

Description: ‎865 Chipset Graphics Controller

Media class: ‎DISPLAY_VGA

Connection
Bus: ‎PCI

Bus PCI #: ‎0

PCI device #: ‎2

PCI function #: ‎0

Vendor ID: ‎0x8086

Device ID: ‎0x2572

Sub vendor ID: ‎0x1028

Sub device ID: ‎0x019d

Misc
Module: ‎Card:Intel 865

Code: Select all

# File generated by XFdrake (rev 57713)

# **********************************************************************
# Refer to the xorg.conf man page for details about the format of
# this file.
# **********************************************************************

Section "Files"
    # font server independent of the X server to render fonts.
    FontPath "unix/:-1"
    
    # minimal fonts to allow X to run without xfs
    FontPath "/usr/share/fonts/misc:unscaled"
EndSection

Section "Extensions"
    Option "Composite"
EndSection

Section "ServerFlags"
    #DontZap # disable <Crtl><Alt><BS> (server abort)
    #DontZoom # disable <Crtl><Alt><KP_+>/<KP_-> (resolution switching)
    AllowMouseOpenFail # allows the server to start up even if the mouse does not work
EndSection

Section "Module"
    Load "dbe" # Double-Buffering Extension
    Load "v4l" # Video for Linux
    Load "extmod"
    Load "type1"
    Load "freetype"
    Load "glx" # 3D layer
    Load "dri" # direct rendering
EndSection

Section "InputDevice"
    Identifier "Keyboard1"
    Driver "kbd"
    Option "XkbModel" "pc105"
    Option "XkbLayout" "us"
    Option "XkbOptions" "compose:rwin"
EndSection

Section "InputDevice"
    Identifier "Mouse1"
    Driver "mouse"
    Option "Protocol" "ExplorerPS/2"
    Option "Device" "/dev/mouse"
EndSection

Section "Monitor"
    Identifier "monitor1"
    VendorName "Plug'n Play"
    ModelName "DELL E153FP"
    HorizSync 30-63
    VertRefresh 56-76
    
    # TV fullscreen mode or DVD fullscreen output.
    # 768x576 @ 79 Hz, 50 kHz hsync
    ModeLine "768x576"     50.00  768  832  846 1000   576  590  595  630
    
    # 768x576 @ 100 Hz, 61.6 kHz hsync
    ModeLine "768x576"     63.07  768  800  960 1024   576  578  590  616
EndSection

Section "Device"
    Identifier "device1"
    VendorName "Intel Corp."
    BoardName "Intel 865"
    Driver "i810"
    Option "DPMS" "false"
    Option "May_Need_ForceBIOS" "1"
    Option "XaaNoOffscreenPixmaps" "1"
EndSection

Section "Screen"
    Identifier "screen1"
    Device "device1"
    Monitor "monitor1"
    DefaultColorDepth 16
    
    Subsection "Display"
        Depth 8
        Modes "1024x768" "832x624" "800x600" "640x480" "480x360" "320x240"
    EndSubsection
    
    Subsection "Display"
        Depth 15
        Modes "1024x768" "832x624" "800x600" "640x480" "480x360" "320x240"
    EndSubsection
    
    Subsection "Display"
        Depth 16
        Modes "1024x768" "832x624" "800x600" "640x480" "480x360" "320x240"
    EndSubsection
    
    Subsection "Display"
        Depth 24
        Modes "1024x768" "832x624" "800x600" "640x480" "480x360" "320x240"
    EndSubsection
EndSection

Section "ServerLayout"
    Identifier "layout1"
    InputDevice "Keyboard1" "CoreKeyboard"
    InputDevice "Mouse1" "CorePointer"
    Screen "screen1"
EndSection
Attachments
wNOPdump.tar.gz
(11.83 KiB) Downloaded 481 times
Taking Puppy Linux to the limit of perfection. meanwhile try "puppy pfix=duct_tape" kernel parem eater.
X86: Sager NP6110 3630QM 16GB ram, Tyan Thunder 2 2x 300Mhz
Sun: SS2 , LX , SS5 , SS10 , SS20 ,Ultra 1, Ultra 10 , T2000
Mac: Platinum Plus, SE/30

titanreign
Posts: 56
Joined: Fri 19 Jan 2007, 14:06
Contact:

Nvidia 6200 xorg.conf using both dvi and crt outputs...

#55 Post by titanreign »

Here's what I've got going on this so far.
I'm using an Nvidia 6200.

With this xorg.conf I have it ignoring the intel onboard graphics, with full 3-D, glx, and whatever else all that stuff is...
This config is allowing me to use the xinerama extension, and have one large cube for both of my screens, or an individual cube for each, or each of the 4 sides of each cube, in an octagon, on each screen. I'd figured I'd post it in this thread to maybe help anyone out who could use it.

Code: Select all

# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings:  version 1.0  (buildmeister@builder3)  Wed Sep 12 14:30:30 PDT 2007

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 1.0  (buildmeister@builder3)  Wed Sep 12 14:29:35 PDT 2007
#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************
# **********************************************************************
# Server flags section.
# **********************************************************************
#everything past here is auto-generated by Puppy's Xorg Wizard...
#PuppyHardwareProfile=NVIDIA

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
    RgbPath         "/usr/X11R7/lib/X11/rgb"
    FontPath        "/usr/X11R7/lib/X11/fonts/misc/"
    FontPath        "/usr/X11R7/lib/X11/fonts/Type1/"
    FontPath        "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection

Section "Module"

# This loads the DBE extension module.
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
# This loads the font modules
    Load           "dbe"  	# Double buffer extension
    SubSection     "extmod"
        Option         "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection
    Load           "type1"
    Load           "freetype"
# This loads the GLX module
    Load           "glx"
# This loads xtrap extension, used by xrandr
    Load           "xtrap"
EndSection

Section "ServerFlags"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.
#    Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
# Removed Option "Xinerama" "0"
# Removed Option "Xinerama" "1"
    Option         "RandR" "on"
    Option         "Xinerama" "0"
EndSection

Section "InputDevice"
    Identifier     "Keyboard0"
    Driver         "kbd"
    Option         "XkbRules" "xorg"
    Option         "XkbModel" "pc102"
    Option         "XkbLayout" "us" #xkeymap0
EndSection

Section "InputDevice"

	#Option      "Emulate3Timeout" "50"
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "IMPS/2" #mouse0protocol
    Option         "Device" "/dev/mouse"
	#Option      "Emulate3Buttons"
    Option         "ZAxisMapping" "4 5" #scrollwheel
EndSection

Section "Modes"

	#modes0modeline0
    Identifier         "Modes0"
EndSection

Section "Monitor"

	#UseModes     "Modes0" #monitor0usemodes
    Identifier     "Monitor0"
    VendorName     "Unknown"
    ModelName      "DELL  M991"
    HorizSync       30.0 - 96.0
    VertRefresh     50.0 - 160.0
EndSection

Section "Monitor"
    Identifier     "Monitor1"
    VendorName     "Unknown"
    ModelName      "HP MX70"
    HorizSync       30.0 - 70.0
    VertRefresh     47.0 - 120.0
EndSection

Section "Device"

 #card0driver
    Identifier     "Card0"
    Driver         "nvidia"
    VendorName     "nVidia Corporation"
    BoardName      "NV44A [GeForce 6200]"
EndSection

Section "Device"
    Identifier     "Videocard0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce 6200"
EndSection

Section "Device"
    Identifier     "Videocard1"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce 6200"
    BusID          "PCI:1:9:0"
    Screen          1
EndSection

Section "Screen"
# Removed Option "TwinView" "0"
# Removed Option "metamodes" "CRT-0: 1280x1024 +0+0"
    Identifier     "Screen0"
    Device         "Videocard0"
    Monitor        "Monitor0"
    DefaultDepth    24
    Option         "RenderAccel" "True"
    Option         "AllowGLXWithComposite" "True"
    Option         "AddARGBGLXVisuals" "True"
    Option         "DisableGLXRootClipping" "True"
    Option         "TwinView" "1"
    Option         "metamodes" "CRT-0: 1280x1024 +0+0, CRT-1: 1280x1024 +1280+0"
    SubSection     "Display"
        Depth       24
    EndSubSection
EndSection

Section "Screen"
    Identifier     "Screen1"
    Device         "Videocard1"
    Monitor        "Monitor1"
    DefaultDepth    24
    Option         "RenderAccel" "True"
    Option         "AllowGLXWithComposite" "True"
    Option         "AddARGBGLXVisuals" "True"
    Option         "DisableGLXRootClipping" "True"
    Option         "TwinView" "0"
    Option         "metamodes" "CRT-1: 1280x1024 +0+0"
EndSection

Section "Extensions"
    Option         "Composite" "Enable"
EndSection
Keep in mind, the options for how many cubes and how they're rendered is in the options of the compizconfig settings manager.
But to get those options and have them work correctly, your xorg.conf must be configured correctly.


Image
[url=http://www.uptime-project.net/profile.php?uid=115727][img]http://img.uptime-project.net/img/8/115727.png[/img][/url]

User avatar
teajay
Posts: 2
Joined: Fri 23 Nov 2007, 07:37
Location: Melbourne, Australia
Contact:

#56 Post by teajay »

I'm not too familiar with Linux so I can't run your script but everything is running well on my Dell Inspiron 9300 with Pentium M, GeForce Go 6800 and 2Gig RAM. I turned off some of effects because the shadows weren't rendering too well (funny blockiness to them).

So many options in Linux it's easy to get confused! Having a USB Drive to run linux from, though, helps to make the transition more friendly.

User avatar
tombh
Posts: 422
Joined: Fri 12 Jan 2007, 12:27
Location: Bristol, UK
Contact:

#57 Post by tombh »

Caneri & The Jinx
It suddenly occured to me that if the radeon driver does not support 5th generation ATI cards like yours then what do you do in ordinary Puppy? Do you just have to use the generic Xorg vesa driver all the time? There is an open source radeon driver that is being developed to run your cards, it's called "radeonhd". However, it's not currently in Puppy and currently lacks 3D support.

Caneri
Sounds like it worked. The acid test is:

Code: Select all

lsmod | grep fglrx
If that doesn't return nothingness then we're in business. If you can send me a wNOPdump from within that booted session containing the installed ati.pet then I can check it out and post you a personalised xorg.conf that will enable Compiz-Fusion :)

The Jinx
Ah yes okay, I'll clarify that a bit: The ATI website has a 43MB program that will compile and install the most recent ATI driver. In order to run this installer you need devx_301.sfs (60MB) and kernel-source_301.sfs(56MB) aswell, so that's about 160MB just for a video driver! Not very 'Puppy'! So what I did was to do it all myself and then save and compress the result -- thus creating the ATI-8.42.3.pet weighing in at just 13MB and consisting of a single download. Much more 'Puppy' :) However, as I said, I am not able to test if it works as I don't have a new enough ATI card (but you do).

Right, so to test you can follow the instructions I gave previously, but just to recap:
(1) Boot into a Puppy session you are willing to lose as uninstalling the ATI.pet is rather complicated.
(2) Download or copy (using a USB stick for example) the ATI.pet and install it by double clicking on it.
(3) Upon completion, type into the terminal:

Code: Select all

aticonfig --initial

(4) Judging by Caneri's experience a full reboot might be best, therefore you will need to create a pup_save file if you haven't already so that all your changes don't get lost.

If the desktop appears then you have success, then post me a wNOPdump (see the very first post of this thread) and I can setup Compiz-Fusion for you. Let me know how it goes.

As for the forum not working, I think that applied to everyone! And the video not working properly in wNOP is very likely a sympton of generic drivers. Do you have the same issue with other versions of Puppy?

cb88
Did you try pakt's fix for Intel cards? Basically:

Code: Select all

modprobe -n i915
modprobe i915
restart X
Bob's yer uncle :)

titanreign
Octagon :shock:

teajay
Thanks for the confirmation. It's great that wNOP is inspiring you to consider the possibility of using a computer without MS Windows.

Caneri
Posts: 1513
Joined: Tue 04 Sep 2007, 13:23
Location: Canada

#58 Post by Caneri »

lsmod | grep fglrx...returned nothing..rats.

I also have no aticonfig file in /usr/bin..thus no aticonfig --initial

The install broke form my playing around too much.. so I need to restart a new install...

As for what I did for 3d before..I only had it running once and lost it when I forgot to use puppy pfix=ram on a test run for a new puppy release.

I'll look again later tonight....I just gotta wobble!

EDIT..Nov23..I am not going to have time to test for awhile...I have to get some other work done...I'll be following and get back when I can...rats
[color=darkred][i]Be not afraid to grow slowly, only be afraid of standing still.[/i]
Chinese Proverb[/color]

Caneri
Posts: 1513
Joined: Tue 04 Sep 2007, 13:23
Location: Canada

#59 Post by Caneri »

ok...work can wait...just gotta wobble ;)

The beauty of puppy is to reinstall an OS is measured in minutes...you just have to love that.

I have a dump file this time..and I didn't have to do a pupsave...dunno why..I did a save anyway so I can get back to where I left off.

alas no output from lsmod | grep fglrx....

ATI Mobility Radeon X1600/256mb (M56 71C5)
Attachments
wNOPdump.tar.gz
(11.27 KiB) Downloaded 495 times

User avatar
tombh
Posts: 422
Joined: Fri 12 Jan 2007, 12:27
Location: Bristol, UK
Contact:

#60 Post by tombh »

Thanks Caneri. I see what the problem is -- the directory structure of the ati dotpet is wrong, I'm going to have to try another way of packaging up the dotpet -- I've got a lot to learn about it so I'll probably take my time over it. I've removed the link from my previous post. Meanwhile, you could always try the devx and kernel-source method I mentioned before, that will automatically put the ati driver files in the correct directories. Either way here is your personalised xorg.conf for when the driver is properly installed. If you do use the devx/kernel method you won't need to run aticonfig afterwards, just replace your xorg.conf with the one I edited for you. Please feel free to ask for any help if you try this way. I mean I have to get this ati.pet working anyway cos it will be essential to wNOP2.

Post Reply