Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Sat 30 Aug 2014, 22:32
All times are UTC - 4
 Forum index » Advanced Topics » Hardware » Video
How to build fglrx 8.42.3? (Fixed)
Post_new_topic   Reply_to_topic View_previous_topic :: View_next_topic
Page 1 of 1 Posts_count  
Author Message
bezeen

Joined: 16 Nov 2007
Posts: 10

PostPosted: Fri 16 Nov 2007, 12:04    Post_subject:  How to build fglrx 8.42.3? (Fixed)  

I'm a noob to Linux - and I have done my google...

I'm very happy with my wnopPuppy - I couldnt get the wobbelido to work. But almost every thing a did worked (not rss in conky). So I'd like to try to make it happen with fglrx-aixgl.

I did a little googling but only get howto make .deb and .rpm of ati*.run and that isnt it.

So howto "make" ? an install on Puppy/Slackware.

(I think it should be like - make... something)

Edited_time_total
Back to top
View user's profile Send_private_message 
cb88


Joined: 28 Jan 2007
Posts: 1169
Location: USA

PostPosted: Fri 16 Nov 2007, 14:12    Post_subject:  

you need to download the dev_xxx.sfs (xxx is the version number) file for your verison of puppy (should be 3.00 for wNOP) and copy it to /mnt/home and reboot now after rebooting you will fine that a c++ development environment has been added automatically to your system

so use it you need to open a command propmt (the terminal from now on) and cd to the directory where your code to compile is...

http://distro.ibiblio.org/pub/linux/distributions/puppylinux/sfs_modules-3/

like this cd /root/directory replace /root/directory with the path to your source code folder...

after you cd (change directory) to the the source directory type

./configue and press enter

then make enter

then make install enter

that will hopefully install the program

when ussing the terminal you can press tab to auto complete some paths and commands.....

_________________
Taking Puppy Linux to the limit of perfection. meanwhile try "puppy pfix=duct_tape" kernel parem eater.
X86: Sager NP6110 3630QM 16GB ram, Tyan Thunder 2 2x 300Mhz
Sun: SS2 , LX , SS5 , SS10 , SS20 ,Ultra 1, Ultra 10 , T2000
Mac: Platinum Plus, SE/30
Back to top
View user's profile Send_private_message Visit_website 
bezeen

Joined: 16 Nov 2007
Posts: 10

PostPosted: Fri 16 Nov 2007, 17:01    Post_subject:  

I used /Puppy setup/bootmanager to start xxx.sfs

and ati's instructions:
Automatic Driver Installation Option

To install the ATI Proprietary Linux driver using the Automatic option, follow these steps:
Launch the Terminal Application/Window and navigate to the ATI Proprietary Linux driver download.
Enter the command ati-driver-installer-7-11-x86.x86_64.run to launch the ATI Proprietary Linux driver installer. The ATI Proprietary Linux Driver Setup dialog box is displayed.

success (ati 7.11 - the new ...run)

and tnx cb88
Back to top
View user's profile Send_private_message 
dbmix

Joined: 03 May 2008
Posts: 16

PostPosted: Thu 08 May 2008, 15:18    Post_subject:  

I did a full install. I can't figure out how to install the squash file...or if it is even possible. There doesn't seem to be any /mnt/home directory. I placed the DEV squash file where I fond another squash file, but it doesn't get installed and the bootmanager complains that there is nothing in the Home directory
Back to top
View user's profile Send_private_message 
muggins

Joined: 20 Jan 2006
Posts: 6683
Location: lisbon

PostPosted: Fri 09 May 2008, 19:26    Post_subject:  

dbmix,

with a full install you need to mount the devx .sfs file, then copy everything from the temporary mount-point to your hard disk. See here, down the bottom:

http://puppylinux.com/hard-puppy.htm
Back to top
View user's profile Send_private_message 
Display_posts:   Sort by:   
Page 1 of 1 Posts_count  
Post_new_topic   Reply_to_topic View_previous_topic :: View_next_topic
 Forum index » Advanced Topics » Hardware » Video
Jump to:  

Rules_post_cannot
Rules_reply_cannot
Rules_edit_cannot
Rules_delete_cannot
Rules_vote_cannot
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0483s ][ Queries: 12 (0.0057s) ][ GZIP on ]