The video card is a Silicon Motion SM710 LynxEM. The monitor is an 800x600 LCD with a 60Hz to 75Hz refresh ( i think). If I can get this working I'll move on to the touch screen. THanks in advance.
Here's what my xorg.conf looks like
Code: Select all
#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
Load "synaptics"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"
# This loads the GLX module
Load "glx"
# This loads xtrap extension, used by xrandr
Load "xtrap"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
# Option "RandR" "on"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
InputDevice "Synaptics Mouse" "AlwaysCore"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "us" #xkeymap0
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "InputDevice"
Identifier "Synaptics Mouse"
Driver "synaptics"
Option "Device" "/dev/psaux"
Option "Protocol" "auto-dev"
Option "LeftEdge" "120"
Option "RightEdge" "930"
Option "TopEdge" "120"
Option "BottomEdge" "650"
Option "FingerLow" "14"
Option "FingerHigh" "15"
Option "MaxTapTime" "0"
Option "MaxTapMove" "110"
Option "VertScrollDelta" "20"
Option "MinSpeed" "0.3"
Option "MaxSpeed" "0.75"
Option "AccelFactor" "0.030"
Option "EdgeMotionMinSpeed" "200"
Option "EdgeMotionMaxSpeed" "200"
Option "UpDownScrolling" "1"
Option "CircularScrolling" "1"
Option "CircScrollDelta" "0.1"
Option "CircScrollTrigger" "2"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5
VertRefresh 40-70
#UseModes "Modes0" #monitor0usemodes
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "pci_burst" # [<bool>]
#Option "fifo_conservative" # [<bool>]
#Option "fifo_moderate" # [<bool>]
#Option "fifo_aggressive" # [<bool>]
#Option "pci_retry" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "set_mclk" # <freq>
#Option "show_cache" # [<bool>]
#Option "HWCursor" # [<bool>]
#Option "SWCursor" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "ByteSwap" # [<bool>]
#Option "Interlaced" # [<bool>]
#Option "UseBIOS" # [<bool>]
#Option "ZoomOnLCD" # [<bool>]
#Option "Dualhead" # [<bool>]
#Option "AccelMethod" # <str>
Identifier "Card0"
Driver "siliconmotion" #card0driver
VendorName "Silicon Motion, Inc."
BoardName "SM710 LynxEM"
BusID "PCI:0:2:0"
Option "UseBIOS" "ON"
ChipSet "lynxem"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
Subsection "Display"
Depth 24
Modes "800x600" "640x480"
EndSubsection
EndSection
#PuppyHardwareProfile=Silicon_Motion_SM710