How do I install Puppy to a slave hard drive?
How do I install Puppy to a slave hard drive?
I have 2 hard drives, one with windows (the master), and one currently blank(the slave). I want to put on the blank slave. Is this possible? If so, can someone guide me step by step from puppys start up, to installing it on my slave? Thanx!
it should be possible
i usually run Puppy from a poor man's install ... just copy 3 file (vmlinuz, image.gz, and usr_cram.fs) to your hard drive ... and Puppy is installed
the 3 files take up about 60 megs of space ... you hardly need a whole drive for that
you can setup a Linux partition, and copy all the Puppy files in /bin, /sbin, /etc, /lib, /usr and so on, to your hard drive, but it won't run any better
you might want to do this if your computer has very little memory, maybe 64 megs or 32 megs ... or if you want to do some complex development, but then you would not be asking this question
if you have never installed Puppy on your hard drive before, why not do it the easy way, an "option 1" "poor man's install" (just copy 3 files to your hard drive)?
i usually run Puppy from a poor man's install ... just copy 3 file (vmlinuz, image.gz, and usr_cram.fs) to your hard drive ... and Puppy is installed
the 3 files take up about 60 megs of space ... you hardly need a whole drive for that
you can setup a Linux partition, and copy all the Puppy files in /bin, /sbin, /etc, /lib, /usr and so on, to your hard drive, but it won't run any better
you might want to do this if your computer has very little memory, maybe 64 megs or 32 megs ... or if you want to do some complex development, but then you would not be asking this question
if you have never installed Puppy on your hard drive before, why not do it the easy way, an "option 1" "poor man's install" (just copy 3 files to your hard drive)?
There are so many ways to boot Puppy. If I have MS-DOS as the primary boot device, I'd use GRUB for DOS. Make a config.sys menu system as follows:
In the C:\BOOT\GRUB directory you will have:
Code: Select all
[menu]
menuitem=puppy, Puppy
menuitem=msdos, MS-DOS
menucolor=15,1
menudefault=puppy,10
[common]
;switches /f/n
[puppy]
install=c:\boot\grub\grub.exe
[msdos]
;; put your own commands here for dos
; example only:
dos=high
device=c:\dos\himem.sys
- * GRUB.EXE
* MENU.LST
Code: Select all
timeout 0
title Puppy
rootnoverify (hd1,0)
kernel (hd1,0)/vmlinuz root=/dev/ram PFILE=pup001-none-262144 PHOME=hdb1
initrd (hd1,0)/image.gz
install on slave
try this:
disconect the master disk leaving only the slave (no other, not even usb)
Boot from cd
run hd install script
partition it and install
when asked to install grub , install it into the mbr,
make shure you enter the correct disk and partition (ex:/dev/hdb1)
once its finished use rox to goto /boot/grub
open menu.lst
check that the entries boot and root refer to the slave disk (grub uses hd0,0 , ej hdDISC,PARTITION).
turn off computer
reconect disks , autodetect them and select to boot from ide-1 or the D,E or whatever disk is your slave in the bios
If the boot fails, then try and edt the boot options in the grub menu (just press E). If the boot option is set to hd0,0 and faild the try hd1,0.
That may depend on your bios
Thats how i installed it and it worked. good luck
disconect the master disk leaving only the slave (no other, not even usb)
Boot from cd
run hd install script
partition it and install
when asked to install grub , install it into the mbr,
make shure you enter the correct disk and partition (ex:/dev/hdb1)
once its finished use rox to goto /boot/grub
open menu.lst
check that the entries boot and root refer to the slave disk (grub uses hd0,0 , ej hdDISC,PARTITION).
turn off computer
reconect disks , autodetect them and select to boot from ide-1 or the D,E or whatever disk is your slave in the bios
If the boot fails, then try and edt the boot options in the grub menu (just press E). If the boot option is set to hd0,0 and faild the try hd1,0.
That may depend on your bios
Thats how i installed it and it worked. good luck
Try this
Or try to keep it simple: http://www.ph-islands.net/pupinstall/winxp.php