Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Sun 23 Nov 2014, 14:44
All times are UTC - 4
 Forum index » Advanced Topics » Additional Software (PETs, n' stuff) » Utilities
sakura-2.4.2 + vte-0.28.2
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 1 [5 Posts]  
Author Message
Karl Godt


Joined: 20 Jun 2010
Posts: 3972
Location: Kiel,Germany

PostPosted: Sat 07 Apr 2012, 13:10    Post subject:  sakura-2.4.2 + vte-0.28.2  

This is sakura compiled on racy 5.3 on an Asus-1005HAG/HGO netbook frugal installed on micro sd card 1GB RAM, no swap .

They have been compiled simply './configure' OR 'cmake . && make' .

They go to /usr/local/*

They are split into EXE,DOC,DEV,NLS .

The .pets are packed into this single .sfs NOT to be able to load it at boot time, but for simply clicking on the .sfs to access the .pets .

The .pets should install as usual .

Since racy uses a glic-2.10.1 I guess they should run on Lupu/Lucid glibc-2.11.x and Slacko glibc-2.13.x .

I don't expect them to run on Puppy4 glibc-2.6.1 and LighthousePup-443 glibc-2.9.x .

For these Puppies please check out :

Sakura Terminal Emulator
by aragon

sakura-2.3.4-i486.pet
by runtt21

*
Homepage of sakura :
https://launchpad.net/ubuntu/+source/sakura/2.4.2-3
Got vte from here :
http://packages.debian.org/source/sid/vte
*
SAKURA-2.4.2+vte-0.28.2.sfs.tar
Description  the ".tar" is fake to be able to upload . Just remove the ".tar" extension to be able to click/mount the .sfs
tar

 Download 
Filename  SAKURA-2.4.2+vte-0.28.2.sfs.tar 
Filesize  1.53 MB 
Downloaded  564 Time(s) 
Back to top
View user's profile Send private message Visit poster's website 
Karl Godt


Joined: 20 Jun 2010
Posts: 3972
Location: Kiel,Germany

PostPosted: Sun 08 Apr 2012, 04:25    Post subject:  

Update :

Just tested the installation on a dpup-005 by iguleder which runs the
stock 'linux_kernel-2.6.33.2-tickless_smp_patched-L3.pet'
with glibc-2.11.2
which came out in the time of Lupu-511

and it worked out_of_the_box just installing the two mains

sakura-2.4.2-i686.pet
vte-0.28.2-i686.pet

from the above attached .sfs

They both have a size of 'ls -s -> 405KB' which should expand to approx. 1,6MB installed .

I like urxvt too, but it is lacking tabs, the possibility for a background image and most important, it is possible to scroll back in sakura even when there is output from for example ' make ' .

A small note : When adjusting the options in sakura, please close sakura and launch it again, for new instances of sakura won't read '$HOME/.config/sakura/sakura.conf' if another instance of sakura is running .

Enjoy !
sakura-2.4.2-pet.png
 Description   
 Filesize   171.66 KB
 Viewed   1267 Time(s)

sakura-2.4.2-pet.png

Back to top
View user's profile Send private message Visit poster's website 
Pete22


Joined: 08 May 2009
Posts: 241
Location: Utah, USA

PostPosted: Thu 12 Apr 2012, 15:55    Post subject:  

I downloaded this in to saluki. I did not get the pretty screen like you got.

Can you help me?

Pete
Back to top
View user's profile Send private message 
Karl Godt


Joined: 20 Jun 2010
Posts: 3972
Location: Kiel,Germany

PostPosted: Thu 12 Apr 2012, 18:28    Post subject:  

The opacity can be adjusted by the right-click menu : Options > Set opacity level . The lesser , the more transparent .

For the background : attached default background from iguleders dpup series (007, was last with default 2.6.33.2 kernel, later had 2.6.35/36 kernels ) .
default.jpg.bz2
Description 
bz2

 Download 
Filename  default.jpg.bz2 
Filesize  160.26 KB 
Downloaded  436 Time(s) 
sakura_set_opacity.png
 Description   
 Filesize   790.47 KB
 Viewed   1206 Time(s)

sakura_set_opacity.png

Back to top
View user's profile Send private message Visit poster's website 
Karl Godt


Joined: 20 Jun 2010
Posts: 3972
Location: Kiel,Germany

PostPosted: Sun 17 Jun 2012, 18:11    Post subject:  

Just wanted to note, that because of configured to /usr/local i had to run
Code:
ldconfig

on one Puppy to make it find the vte libs .

And another thing to mention are windowmanagers like enlightenment e17 or some pure Xserver backgrounds that somehow are not able to work with the transparency option in sakura .
Back to top
View user's profile Send private message Visit poster's website 
Display posts from previous:   Sort by:   
Page 1 of 1 [5 Posts]  
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » Advanced Topics » Additional Software (PETs, n' stuff) » Utilities
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0504s ][ Queries: 13 (0.0042s) ][ GZIP on ]