Puppy Linux Discussion Forum

[Semme]

You didn't comment on anything I asked. On top'a that- you got ahead of yourself.

For wired, try the first here. I'm not sure which mode your phone's gotta be in..

[Karl Godt]

It seems that the bluetooth driver is loaded : rfcomm ..

It seems that bluez package is not installed correctly ..

While i was trying to compile cups i compiled bluez without having the need for it :

Simply configured on Puppy 4.3.1 -> likely runs on later Puppies ;

goes to /usr/local/bin .. /lib .. /share .. /doc BUT /etc ! -i686 !

[alwaysalonee]

sorry seeme for being an idiot ..
i wanna have fun in vacation but this puppy bluetooth thing screwing it up ..
i am now trying with cable thing first ...

Update :
lol turns out that USB cable is damaged and weirdly can be used to only transfer the data
i guess now i wil need to stick with bluetooth ..

screenshot

[trapster]

After you get bluetooth working, See Here for how I connected to a Samsung Instinct.

I think it was in Pupeee that Jemimah put out.

[alwaysalonee]

hi guys ...
i am very near to get bluetooth working ..
thanks to trapster , semme and all ..
the mobile is connecting and it' sdoing usual process to connect to the internet , but then mobile says 'subscribe to data connection' which i already have so the problem seems to be with "APN" or other some phone setting in wvdial.conf

i run this commands ..
sh-4.1# hcitool scan
sh-4.1# sdptool browse 18:14:56:CA:9E:42
sh-4.1# rfcomm connect 0 18:14:56:CA:9E:42 3
in other console : wvdial

the wvdial.conf looks like ...

[Modem0]
Modem = /dev/ttyACM0
Baud = 115200
SetVolume = 0
DialCommand = ATDT
Init = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2
Init3 = ATM0

[Dialer test]
Username = ""
Password = ""
Phone = #91
Init1 = ATZ
ISDN = 0
Modem Type = Analog Modem
Auto Reconnect = on
Carrier Check = no
Stupid Mode = 1
Inherits = Modem0

[Dialer al]
Modem = /dev/rfcomm0
Baud = 115200
Init1 = AT+CGDCONT=1,"IP","TATA.DOCOMO.INTERNET"
Init2 = ate0q0v1
Init3 = at
Init4 = at
#FlowControl = CRTSCTS
Phone = *99#
Username = <phone number>
Password = <password>
Ask Password = 0
Dial Command = ATDT
Stupid Mode = 1
CompuServe = 0
Idle Seconds = 300
ISDN = 0

[Dialer Defaults]
Modem = /dev/rfcomm0
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2
stupid mode = 1
Modem Type = Analog Modem
Phone = *99***#
ISDN = 0
Username = a
Password = b
Baud = 460800

; Phone =
; Username =
; Password =

check pastebin for console command and it's results
Link : http://pastebin.com/1mbbY5ib
please help and thanks ..

[Semme]

Here's your exit code: "The link was terminated because the peer is not responding to echo requests."

Is this how you have your phone set up? Pages 20 and 21 for pairing.

After you run the above mobile routine, is there anything that stands out in /var/log/messages?

[Karl Godt]

it is normally not possible to connect to the device by two programs.

most programs lock /dev/tty* by a lock file in /var/run/*

for example : if i am having "cu -l /dev/ttyUSB0" running , pppd on another console would refuse to connect .

i am wondering which config file your pppd uses ?

the echo requests things can be adjusted in /etc/ppp/peers/gprsmm file for pgprs-connect .

[alwaysalonee]

Hello Seeme , Trapster , Karl.. ..
in my nokio phone i selected option to stay online always option and now it's working fine thanks guys for all the help

Thanks a lot guys it's my first post from puppy linux
Thanks a lot ....

[Semme]

GREAT! You appear very happy? I take your vacation's going a bit better now?

[alwaysalonee]

yes thanks a lot for that seeme

[Semme]

ENJOY!