Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Wed 23 Apr 2014, 02:27
All times are UTC - 4
 Forum index » Advanced Topics » Hardware » Networking » Wireless
Need driver for Atheros AR9287 in Lucid 528 (SOLVED)
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 1 [14 Posts]  
Author Message
nilsonmorales


Joined: 15 Apr 2011
Posts: 420
Location: El salvador

PostPosted: Wed 30 Jan 2013, 11:14    Post subject:  Need driver for Atheros AR9287 in Lucid 528 (SOLVED)  

Lucid 5.2.8 please or any clue

lspci -nn show this
00:07.0 Network controller [0280]: Atheros Communications Inc. AR9287 Wireless Network Adapter [168c:002d] (rev 01)

tnx in advance

Last edited by nilsonmorales on Mon 04 Feb 2013, 22:14; edited 1 time in total
Back to top
View user's profile Send private message MSN Messenger 
rcrsn51


Joined: 05 Sep 2006
Posts: 8562
Location: Stratford, Ontario

PostPosted: Wed 30 Jan 2013, 11:55    Post subject: Re: Need driver for Atheros AR9287 in Lucid 528?  

In Lucid 528, the ath9k module claims to support your [168c:002d] device.

Run "lsmod". Is this module being loaded?

Then run "dmesg" and look for error messages.

There is some discussion about ath9k here.

Have you tried newer Puppies?
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Wed 30 Jan 2013, 17:34    Post subject:  

this problem is mine actually.
nilsonmorales post it here for me. thanks to him. Smile
i'd ran lsmod and show me this information:


Quote:
Module Size Used by
ndiswrapper 135277 0
iptable_mangle 1189 0
iptable_nat 2666 0
nf_nat 10083 1 iptable_nat
ipt_REJECT 1485 1
nf_conntrack_ftp 4020 0
nf_conntrack_irc 2359 0
iptable_filter 958 1
xt_state 895 4
nf_conntrack_ipv4 7063 7 iptable_nat,nf_nat
nf_conntrack 36999 6 iptable_nat,nf_nat,nf_conntrack_ftp,nf_conntrack_irc,xt_state,nf_conntrack_ipv4
nf_defrag_ipv4 755 1 nf_conntrack_ipv4
ip_tables 7321 3 iptable_mangle,iptable_nat,iptable_filter
joydev 6492 0
snd_intel8x0 19143 0
snd_ac97_codec 75789 1 snd_intel8x0
ac97_bus 686 1 snd_ac97_codec
usbhid 18009 0
snd_cs4236 19799 0
serio_raw 2928 0
snd_wavefront 23070 0
snd_wss_lib 15773 2 snd_cs4236,snd_wavefront
snd_pcm_oss 26845 0
snd_mixer_oss 9963 1 snd_pcm_oss
snd_pcm 45385 5 snd_intel8x0,snd_ac97_codec,snd_cs4236,snd_wss_lib,snd_pcm_oss
snd_page_alloc 4645 3 snd_intel8x0,snd_wss_lib,snd_pcm
snd_opl3_lib 5758 2 snd_cs4236,snd_wavefront
snd_hwdep 3830 2 snd_wavefront,snd_opl3_lib
snd_mpu401 2808 0
snd_mpu401_uart 3899 3 snd_cs4236,snd_wavefront,snd_mpu401
shpchp 21148 0
snd_seq_dummy 907 0
sis900 13650 0
pci_hotplug 18286 1 shpchp
pcspkr 1179 0
mii 2650 1 sis900
ohci_hcd 16937 0
snd_seq_oss 18888 0
ssb 29373 1 ohci_hcd
fbcon 27736 0
tileblit 1509 1 fbcon
font 6916 1 fbcon
snd_seq_midi 3156 0
bitblit 3514 1 fbcon
softcursor 805 1 bitblit
snd_rawmidi 11924 3 snd_wavefront,snd_mpu401_uart,snd_seq_midi
squashfs 15984 0
snd_seq_midi_event 3592 2 snd_seq_oss,snd_seq_midi
snd_seq 32379 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
aufs 110466 0
snd_timer 11986 4 snd_wss_lib,snd_pcm,snd_opl3_lib,snd_seq
fuse 42549 0
snd_seq_device 3601 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
nls_iso8859_1 2937 0
snd 30859 17 snd_intel8x0,snd_ac97_codec,snd_cs4236,snd_wavefront,snd_wss_lib,
snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,
snd_mpu401,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,
snd_timer,snd_seq_device
nls_cp437 4465 0
i2c_sis96x 2389 0
sis_agp 3121 1
soundcore 3403 1 snd
i2c_core 11497 1 i2c_sis96x
agpgart 18904 1 sis_agp
sg 19093 0
ns558 1539 0
gameport 5717 2 ns558
fan 2478 0
ppdev 4090 0
parport_pc 19055 0
thermal 9263 0
parport 20387 2 ppdev,parport_pc
evdev 5517 0
button 3522 0
processor 24987 0
ehci_hcd 25830 0
usbcore 91279 5 ndiswrapper,usbhid,ohci_hcd,ehci_hcd
floppy 40152 0


i cant see the ath9k module if you mean that. I'm newie here really.
i have to install it manually? if so, how can i do that?

before installing frisbee i was able to select the ath9k module when i press the connect button (with the original connect wizard), but now is frisbee instead the original wizard that show up.

when i could use the ath9k driver (whit the original wizard connect), puppy recognizes my pci wireless adapter, but when i ran the scan for search wireless connection, the wizard dont show any.

i dont try newer versions of puppy yet, because i have installed puppy-es passagio 531-02 , that is a spanish supported version of puppy. Smile

Last edited by occiso on Wed 30 Jan 2013, 17:44; edited 1 time in total
Back to top
View user's profile Send private message 
pemasu


Joined: 08 Jul 2009
Posts: 5459
Location: Finland

PostPosted: Wed 30 Jan 2013, 17:43    Post subject:  

Quote:
usbcore 91279 5 ndiswrapper,usbhid,ohci_hcd,ehci_hcd


I suppose you have used the ndiswrapper wizard which suggests to unload loaded wlan driver and you did that. So the ath9k was unloaded and ndiswrapper was loaded instead to use it with .inf file.

So....there should not be ath9k loaded. Simple.
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Wed 30 Jan 2013, 17:59    Post subject:  

pemasu wrote:
Quote:
usbcore 91279 5 ndiswrapper,usbhid,ohci_hcd,ehci_hcd


I suppose you have used the ndiswrapper wizard which suggests to unload loaded wlan driver and you did that. So the ath9k was unloaded and ndiswrapper was loaded instead to use it with .inf file.

So....there should not be ath9k loaded. Simple.


true, that was what i do. but a can't do that now with frisbee (load and unload with ndiswrapper). When i'd loaded the windows drivers with Ndisgwrapper, the wizard wont recognize my pci wireless adapter with the uploaded drivers of windows (i'd tryed with all of them) and ath9k native driver recognize my card, but dont show any wireless connection.

Last edited by occiso on Wed 30 Jan 2013, 22:13; edited 1 time in total
Back to top
View user's profile Send private message 
pemasu


Joined: 08 Jul 2009
Posts: 5459
Location: Finland

PostPosted: Wed 30 Jan 2013, 18:05    Post subject:  

I suggest you to do these tests with virgin base sfs without savefile, for example with pfix=ram boot parameter...and without loading ndiswrapper at all.

Getting the dmesg output for evaluation with ath9k loaded is first step to see what possibly goes wrong.
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Wed 30 Jan 2013, 23:35    Post subject:  

oks, this is what i have done. I've tryed with Precise Puppy version 5.4.3, clean started with a booteable usb. Internet wizard connect started automatically and i've selected "wlan0" with "ath9k" driver... ran the scan for wireless connection, nothing happens (dont show any wireless connection, same problem), then i'd opened the terminal and wrote dmesg and this is what i get (sorry for the large text):

Quote:
0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00037bfe:0004dff0)
[ 0.000000] Memory: 1259444k/1277888k available (3243k kernel code, 17992k reserved, 1370k data, 360k init, 364488k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff17000 - 0xfffff000 ( 928 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
[ 0.000000] .init : 0xc1482000 - 0xc14dc000 ( 360 kB)
[ 0.000000] .data : 0xc132ad47 - 0xc1481580 (1370 kB)
[ 0.000000] .text : 0xc1000000 - 0xc132ad47 (3243 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f6808000 soft=f680a000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1803.129 MHz processor.
[ 0.003340] Calibrating delay loop (skipped), value calculated using timer frequency.. 3607.51 BogoMIPS (lpj=6010430)
[ 0.003357] pid_max: default: 32768 minimum: 301
[ 0.003500] Mount-cache hash table entries: 512
[ 0.007154] CPU0: Hyper-Threading is disabled
[ 0.007167] mce: CPU supports 4 MCE banks
[ 0.007200] CPU0: Thermal monitoring enabled (TM1)
[ 0.007447] SMP alternatives: switching to UP code
[ 0.025619] ACPI: Core revision 20110623
[ 0.030233] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.030617] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.065073] CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 07
[ 0.066663] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.066663] ... version: 0
[ 0.066663] ... bit width: 40
[ 0.066663] ... generic registers: 18
[ 0.066663] ... value mask: 000000ffffffffff
[ 0.066663] ... max period: 0000007fffffffff
[ 0.066663] ... fixed-purpose events: 0
[ 0.066663] ... event mask: 000000000003ffff
[ 0.066663] Brought up 1 CPUs
[ 0.066663] Total of 1 processors activated (3607.51 BogoMIPS).
[ 0.066663] NET: Registered protocol family 16
[ 0.066663] ACPI: bus type pci registered
[ 0.109289] PCI: PCI BIOS revision 2.10 entry at 0xfbb40, last bus=1
[ 0.109297] PCI: Using configuration type 1 for base access
[ 0.112416] bio: create slab <bio-0> at 0
[ 0.112610] ACPI: Added _OSI(Module Device)
[ 0.112617] ACPI: Added _OSI(Processor Device)
[ 0.112623] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.112629] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.113740] ACPI: EC: Look up EC in DSDT
[ 0.118752] ACPI: Interpreter enabled
[ 0.118776] ACPI: (supports S0 S1 S5)
[ 0.118814] ACPI: Using IOAPIC for interrupt routing
[ 0.125283] ACPI: No dock devices found.
[ 0.125301] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.125454] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.125690] pci_root PNP0A03:00: host bridge window [io 0x0000-0x047f] (ignored)
[ 0.125699] pci_root PNP0A03:00: host bridge window [io 0x0490-0x0cf7] (ignored)
[ 0.125708] pci_root PNP0A03:00: host bridge window [io 0x0d00-0x0fff] (ignored)
[ 0.125716] pci_root PNP0A03:00: host bridge window [io 0x1100-0xffff] (ignored)
[ 0.125724] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.125733] pci_root PNP0A03:00: host bridge window [mem 0x4e000000-0xfebfffff] (ignored)
[ 0.125782] pci 0000:00:00.0: [1039:0651] type 0 class 0x000600
[ 0.125806] pci 0000:00:00.0: reg 10: [mem 0xe8000000-0xebffffff]
[ 0.125950] pci 0000:00:01.0: [1039:0001] type 1 class 0x000604
[ 0.126029] pci 0000:00:02.0: [1039:0008] type 0 class 0x000601
[ 0.126134] pci 0000:00:02.0: Enabling SiS 96x SMBus
[ 0.126175] pci 0000:00:02.1: [1039:0016] type 0 class 0x000c05
[ 0.126247] pci 0000:00:02.1: reg 20: [io 0x10c0-0x10df]
[ 0.126318] pci 0000:00:02.5: [1039:5513] type 0 class 0x000101
[ 0.126369] pci 0000:00:02.5: reg 10: [io 0x01f0-0x01f7]
[ 0.126387] pci 0000:00:02.5: reg 14: [io 0x03f4-0x03f7]
[ 0.126405] pci 0000:00:02.5: reg 18: [io 0x0170-0x0177]
[ 0.126422] pci 0000:00:02.5: reg 1c: [io 0x0374-0x0377]
[ 0.126440] pci 0000:00:02.5: reg 20: [io 0x4000-0x400f]
[ 0.126509] pci 0000:00:02.5: supports D2
[ 0.126515] pci 0000:00:02.5: PME# supported from D3cold
[ 0.126526] pci 0000:00:02.5: PME# disabled
[ 0.126566] pci 0000:00:02.7: [1039:7012] type 0 class 0x000401
[ 0.126595] pci 0000:00:02.7: reg 10: [io 0xe000-0xe0ff]
[ 0.126614] pci 0000:00:02.7: reg 14: [io 0xe400-0xe47f]
[ 0.126741] pci 0000:00:02.7: supports D1 D2
[ 0.126747] pci 0000:00:02.7: PME# supported from D3hot D3cold
[ 0.126757] pci 0000:00:02.7: PME# disabled
[ 0.126786] pci 0000:00:03.0: [1039:7001] type 0 class 0x000c03
[ 0.126811] pci 0000:00:03.0: reg 10: [mem 0xed112000-0xed112fff]
[ 0.126923] pci 0000:00:03.1: [1039:7001] type 0 class 0x000c03
[ 0.126948] pci 0000:00:03.1: reg 10: [mem 0xed113000-0xed113fff]
[ 0.127063] pci 0000:00:03.3: [1039:7002] type 0 class 0x000c03
[ 0.127092] pci 0000:00:03.3: reg 10: [mem 0xed110000-0xed110fff]
[ 0.127206] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[ 0.127216] pci 0000:00:03.3: PME# disabled
[ 0.127261] pci 0000:00:04.0: [1039:0900] type 0 class 0x000200
[ 0.127291] pci 0000:00:04.0: reg 10: [io 0xe800-0xe8ff]
[ 0.127312] pci 0000:00:04.0: reg 14: [mem 0xed111000-0xed111fff]
[ 0.127379] pci 0000:00:04.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.127425] pci 0000:00:04.0: supports D1 D2
[ 0.127430] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.127441] pci 0000:00:04.0: PME# disabled
[ 0.127479] pci 0000:00:07.0: [168c:002d] type 0 class 0x000280
[ 0.127509] pci 0000:00:07.0: reg 10: [mem 0xed100000-0xed10ffff]
[ 0.127627] pci 0000:00:07.0: PME# supported from D0 D3hot
[ 0.127636] pci 0000:00:07.0: PME# disabled
[ 0.127743] pci 0000:01:00.0: [1039:6325] type 0 class 0x000300
[ 0.127769] pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[ 0.127785] pci 0000:01:00.0: reg 14: [mem 0xed000000-0xed01ffff]
[ 0.127801] pci 0000:01:00.0: reg 18: [io 0xd000-0xd07f]
[ 0.127881] pci 0000:01:00.0: supports D1 D2
[ 0.127939] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.127952] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.127962] pci 0000:00:01.0: bridge window [mem 0xed000000-0xed0fffff]
[ 0.127973] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe7ffffff pref]
[ 0.127992] pci_bus 0000:00: on NUMA node 0
[ 0.128002] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.128336] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[ 0.147599] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 14 15)
[ 0.147706] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
[ 0.147810] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 14 15)
[ 0.147911] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 14 15)
[ 0.148013] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 14 15)
[ 0.148115] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 14 15)
[ 0.148229] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
[ 0.148334] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 14 15)
[ 0.148526] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.148534] vgaarb: loaded
[ 0.148538] vgaarb: bridge control possible 0000:01:00.0
[ 0.148838] SCSI subsystem initialized
[ 0.149057] libata version 3.00 loaded.
[ 0.149279] usbcore: registered new interface driver usbfs
[ 0.149337] usbcore: registered new interface driver hub
[ 0.149400] usbcore: registered new device driver usb
[ 0.149542] PCI: Using ACPI for IRQ routing
[ 0.149553] PCI: pci_cache_line_size set to 64 bytes
[ 0.149665] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.149674] reserve RAM buffer: 000000004dff0000 - 000000004fffffff
[ 0.150153] pnp: PnP ACPI init
[ 0.150175] ACPI: bus type pnp registered
[ 0.150527] pnp 00:00: [mem 0x000f0000-0x000f3fff]
[ 0.150535] pnp 00:00: [mem 0x000f4000-0x000f7fff]
[ 0.150541] pnp 00:00: [mem 0x000f8000-0x000fbfff]
[ 0.150547] pnp 00:00: [mem 0x000fc000-0x000fffff]
[ 0.150553] pnp 00:00: [mem 0x4dff0000-0x4dffffff]
[ 0.150559] pnp 00:00: [mem 0xffff0000-0xffffffff]
[ 0.150565] pnp 00:00: [mem 0x00000000-0x0009ffff]
[ 0.150571] pnp 00:00: [mem 0x00100000-0x4dfeffff]
[ 0.150577] pnp 00:00: [mem 0xffee0000-0xffefffff]
[ 0.150583] pnp 00:00: [mem 0xfffe0000-0xfffeffff]
[ 0.150589] pnp 00:00: [mem 0xfec00000-0xfecfffff]
[ 0.150595] pnp 00:00: [mem 0xfee00000-0xfeefffff]
[ 0.150692] system 00:00: [mem 0x000f0000-0x000f3fff] could not be reserved
[ 0.150701] system 00:00: [mem 0x000f4000-0x000f7fff] could not be reserved
[ 0.150709] system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.150718] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.150726] system 00:00: [mem 0x4dff0000-0x4dffffff] could not be reserved
[ 0.150735] system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.150743] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.150752] system 00:00: [mem 0x00100000-0x4dfeffff] could not be reserved
[ 0.150761] system 00:00: [mem 0xffee0000-0xffefffff] has been reserved
[ 0.150769] system 00:00: [mem 0xfffe0000-0xfffeffff] has been reserved
[ 0.150777] system 00:00: [mem 0xfec00000-0xfecfffff] could not be reserved
[ 0.150786] system 00:00: [mem 0xfee00000-0xfeefffff] has been reserved
[ 0.150795] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.150909] pnp 00:01: [bus 00-ff]
[ 0.150917] pnp 00:01: [io 0x0cf8-0x0cff]
[ 0.150923] pnp 00:01: [io 0x0000-0x047f window]
[ 0.150929] pnp 00:01: [io 0x0480-0x048f]
[ 0.150935] pnp 00:01: [io 0x0490-0x0cf7 window]
[ 0.150941] pnp 00:01: [io 0x0d00-0x0fff window]
[ 0.150947] pnp 00:01: [io 0x1000-0x10bf]
[ 0.150953] pnp 00:01: [io 0x10c0-0x10ff]
[ 0.150958] pnp 00:01: [io 0x1100-0xffff window]
[ 0.150965] pnp 00:01: [mem 0x000a0000-0x000bffff window]
[ 0.150972] pnp 00:01: [mem 0x4e000000-0xfebfffff window]
[ 0.151058] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.151428] pnp 00:02: [io 0x0010-0x001f]
[ 0.151434] pnp 00:02: [io 0x0022-0x003f]
[ 0.151440] pnp 00:02: [io 0x0044-0x005f]
[ 0.151445] pnp 00:02: [io 0x0062-0x0063]
[ 0.151451] pnp 00:02: [io 0x0065-0x006f]
[ 0.151456] pnp 00:02: [io 0x0074-0x007f]
[ 0.151462] pnp 00:02: [io 0x0091-0x0093]
[ 0.151470] pnp 00:02: [io 0x00a2-0x00bf]
[ 0.151476] pnp 00:02: [io 0x00e0-0x00ef]
[ 0.151482] pnp 00:02: [io 0x04d0-0x04d1]
[ 0.151487] pnp 00:02: [io 0x0294-0x0297]
[ 0.151568] system 00:02: [io 0x04d0-0x04d1] has been reserved
[ 0.151576] system 00:02: [io 0x0294-0x0297] has been reserved
[ 0.151584] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.151614] pnp 00:03: [dma 4]
[ 0.151619] pnp 00:03: [io 0x0000-0x000f]
[ 0.151625] pnp 00:03: [io 0x0080-0x0090]
[ 0.151631] pnp 00:03: [io 0x0094-0x009f]
[ 0.151636] pnp 00:03: [io 0x00c0-0x00df]
[ 0.151687] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.151714] pnp 00:04: [io 0x0070-0x0073]
[ 0.151758] pnp 00:04: [irq 8]
[ 0.151810] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.151832] pnp 00:05: [io 0x0061]
[ 0.151887] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.151911] pnp 00:06: [io 0x00f0-0x00ff]
[ 0.151923] pnp 00:06: [irq 13]
[ 0.151974] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.152182] pnp 00:07: [io 0x03f2-0x03f5]
[ 0.152189] pnp 00:07: [io 0x03f7]
[ 0.152202] pnp 00:07: [irq 6]
[ 0.152207] pnp 00:07: [dma 2]
[ 0.152298] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.152573] pnp 00:08: [io 0x03f8-0x03ff]
[ 0.152585] pnp 00:08: [irq 4]
[ 0.152707] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.153475] pnp 00:09: [io 0x0378-0x037f]
[ 0.153482] pnp 00:09: [io 0x0778-0x077b]
[ 0.153493] pnp 00:09: [irq 7]
[ 0.153498] pnp 00:09: [dma 3]
[ 0.153626] pnp 00:09: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.153723] pnp 00:0a: [irq 12]
[ 0.153795] pnp 00:0a: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.153846] pnp 00:0b: [io 0x0060]
[ 0.153852] pnp 00:0b: [io 0x0064]
[ 0.153863] pnp 00:0b: [irq 1]
[ 0.153930] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.154293] pnp 00:0c: [io 0x0201-0x0207]
[ 0.154299] pnp 00:0c: [io 0x0200]
[ 0.154384] pnp 00:0c: Plug and Play ACPI device, IDs PNPb02f (active)
[ 0.154664] pnp 00:0d: [io 0x0330-0x0331]
[ 0.154676] pnp 00:0d: [irq 10]
[ 0.154778] pnp 00:0d: Plug and Play ACPI device, IDs PNPb006 (active)
[ 0.154798] pnp: PnP ACPI: found 14 devices
[ 0.154804] ACPI: ACPI bus type pnp unregistered
[ 0.191411] Switching to clocksource acpi_pm
[ 0.191469] PCI: max bus depth: 1 pci_try_num: 2
[ 0.191534] pci 0000:00:04.0: BAR 6: assigned [mem 0x50000000-0x5001ffff pref]
[ 0.191545] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.191554] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.191568] pci 0000:00:01.0: bridge window [mem 0xed000000-0xed0fffff]
[ 0.191579] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe7ffffff pref]
[ 0.191615] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.191622] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
[ 0.191630] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.191637] pci_bus 0000:01: resource 1 [mem 0xed000000-0xed0fffff]
[ 0.191644] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xe7ffffff pref]
[ 0.191807] NET: Registered protocol family 2
[ 0.191987] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.192828] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.195966] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.198587] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.198608] TCP reno registered
[ 0.198645] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.198731] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.199238] NET: Registered protocol family 1
[ 0.199453] pci 0000:00:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.276716] pci 0000:00:03.0: PCI INT A disabled
[ 0.276756] pci 0000:00:03.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.353361] pci 0000:00:03.1: PCI INT B disabled
[ 0.353390] pci 0000:00:03.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.353419] pci 0000:00:03.3: PCI INT D disabled
[ 0.353443] pci 0000:01:00.0: Boot video device
[ 0.353451] PCI: CLS 32 bytes, default 64
[ 0.353680] Trying to unpack rootfs image as initramfs...
[ 0.439952] Freeing initrd memory: 1828k freed
[ 0.450646] highmem bounce pool size: 64 pages
[ 0.451143] NTFS driver 2.1.30 [Flags: R/W].
[ 0.451208] msgmni has been set to 1751
[ 0.451595] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.451608] io scheduler noop registered
[ 0.451628] io scheduler cfq registered (default)
[ 0.451885] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.465128] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.736795] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.758123] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.758534] Real Time Clock Driver v1.12b
[ 0.758694] Non-volatile memory driver v1.3
[ 0.760953] brd: module loaded
[ 0.762072] loop: module loaded
[ 0.763926] pata_sis 0000:00:02.5: version 0.5.2
[ 0.764041] pata_sis 0000:00:02.5: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.764096] pata_sis 0000:00:02.5: SiS 962/963 MuTIOL IDE UDMA133 controller
[ 0.764974] scsi0 : pata_sis
[ 0.765182] scsi1 : pata_sis
[ 0.766469] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x4000 irq 14
[ 0.766477] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x4008 irq 15
[ 0.767212] Fixed MDIO Bus: probed
[ 0.767250] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.767306] ehci_hcd 0000:00:03.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.767380] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 0.767502] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[ 0.767669] ehci_hcd 0000:00:03.3: irq 23, io mem 0xed110000
[ 0.776714] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[ 0.776821] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.776829] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.776838] usb usb1: Product: EHCI Host Controller
[ 0.776844] usb usb1: Manufacturer: Linux 3.2.29 ehci_hcd
[ 0.776850] usb usb1: SerialNumber: 0000:00:03.3
[ 0.777101] hub 1-0:1.0: USB hub found
[ 0.777116] hub 1-0:1.0: 6 ports detected
[ 0.777350] 116x: driver isp116x-hcd, 03 Nov 2005
[ 0.777373] driver isp1362-hcd, 2005-04-04
[ 0.777392] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.777464] ohci_hcd 0000:00:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.777501] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 0.777526] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 0.777594] ohci_hcd 0000:00:03.0: irq 20, io mem 0xed112000
[ 0.832063] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.832072] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.832079] usb usb2: Product: OHCI Host Controller
[ 0.832085] usb usb2: Manufacturer: Linux 3.2.29 ohci_hcd
[ 0.832091] usb usb2: SerialNumber: 0000:00:03.0
[ 0.832242] hub 2-0:1.0: USB hub found
[ 0.832255] hub 2-0:1.0: 3 ports detected
[ 0.832416] ohci_hcd 0000:00:03.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.832448] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 0.832469] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 0.832523] ohci_hcd 0000:00:03.1: irq 21, io mem 0xed113000
[ 0.885382] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.885391] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.885398] usb usb3: Product: OHCI Host Controller
[ 0.885404] usb usb3: Manufacturer: Linux 3.2.29 ohci_hcd
[ 0.885410] usb usb3: SerialNumber: 0000:00:03.1
[ 0.885558] hub 3-0:1.0: USB hub found
[ 0.885570] hub 3-0:1.0: 3 ports detected
[ 0.885719] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.885914] sl811: driver sl811-hcd, 19 May 2005
[ 0.885941] r8a66597_hcd: driver r8a66597_hcd, 2009-05-26
[ 0.886066] usbcore: registered new interface driver uas
[ 0.886072] Initializing USB Mass Storage driver...
[ 0.886138] usbcore: registered new interface driver usb-storage
[ 0.886144] USB Mass Storage support registered.
[ 0.886170] usbcore: registered new interface driver ums-alauda
[ 0.886198] usbcore: registered new interface driver ums-datafab
[ 0.886226] usbcore: registered new interface driver ums_eneub6250
[ 0.886255] usbcore: registered new interface driver ums-freecom
[ 0.886285] usbcore: registered new interface driver ums-isd200
[ 0.886314] usbcore: registered new interface driver ums-jumpshot
[ 0.886347] usbcore: registered new interface driver ums-realtek
[ 0.886375] usbcore: registered new interface driver ums-sddr09
[ 0.886404] usbcore: registered new interface driver ums-sddr55
[ 0.886432] usbcore: registered new interface driver ums-usbat
[ 0.886470] usbcore: registered new interface driver ldusb
[ 0.886603] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.887079] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.887100] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.887301] mousedev: PS/2 mouse device common for all mice
[ 0.887518] md: raid0 personality registered for level 0
[ 0.887577] cpuidle: using governor ladder
[ 0.887583] cpuidle: using governor menu
[ 0.888018] usbcore: registered new interface driver usbhid
[ 0.888024] usbhid: USB HID core driver
[ 0.888116] Netfilter messages via NETLINK v0.30.
[ 0.888307] TCP cubic registered
[ 0.888319] NET: Registered protocol family 17
[ 0.888351] Registering the dns_resolver key type
[ 0.888416] Using IPI No-Shortcut mode
[ 0.913368] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.950388] ata1.00: ATA-7: SAMSUNG SP0842N, BH100-35, max UDMA/100
[ 0.950397] ata1.00: 156301488 sectors, multi 16: LBA48
[ 0.950411] ata1.01: ATAPI: HL-DT-ST GCE-8526B, 1.04, max UDMA/33
[ 0.950428] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 0.980357] ata1.00: configured for UDMA/33
[ 0.993594] ata1.01: configured for UDMA/33
[ 0.994202] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP0842N BH10 PQ: 0 ANSI: 5
[ 0.994983] scsi 0:0:1:0: CD-ROM HL-DT-ST CD-RW GCE-8526B 1.04 PQ: 0 ANSI: 5
[ 0.995359] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 0.995471] sd 0:0:0:0: [sda] Write Protect is off
[ 0.995479] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.995521] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.997405] sr0: scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
[ 0.997416] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 0.997598] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 1.032847] sda: sda1 sda2
[ 1.033409] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.083372] usb 1-5: new high-speed USB device number 2 using ehci_hcd
[ 1.161516] Freeing unused kernel memory: 360k freed
[ 1.202491] Floppy drive(s): fd0 is 1.44M
[ 1.207658] usb 1-5: New USB device found, idVendor=0781, idProduct=5567
[ 1.207667] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.207675] usb 1-5: Product: Cruzer Blade
[ 1.207680] usb 1-5: Manufacturer: SanDisk
[ 1.207686] usb 1-5: SerialNumber: 4528821DAA5369AA
[ 1.208332] usb-storage: device found at 2
[ 1.208375] scsi2 : usb-storage 1-5:1.0
[ 1.208501] usb-storage: waiting for device to settle before scanning
[ 1.220544] FDC 0 is a post-1991 82077
[ 1.261763] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.279876] aufs 3.2-20120730
[ 1.287449] fuse init (API version 7.17)
[ 1.453380] Refined TSC clocksource calibration: 1803.071 MHz.
[ 1.453403] Switching to clocksource tsc
[ 1.816455] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input1
[ 2.210875] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 8.02 PQ: 0 ANSI: 0 CCS
[ 2.211684] sd 2:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB)
[ 2.212174] sd 2:0:0:0: [sdb] Write Protect is off
[ 2.212182] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 2.212673] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2.212680] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2.214089] usb-storage: device scan complete
[ 2.215044] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2.215051] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2.216834] sdb: sdb1
[ 2.219171] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2.219178] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2.219186] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 2.524265] kjournald starting. Commit interval 5 seconds
[ 2.524357] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 2.524621] EXT3-fs (sda1): using internal journal
[ 2.524634] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 3.290850] cdrom: sr0: mrw address space DMA selected
[ 3.343780] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 3.355968] ISOFS: changing to secondary root
[ 6.076683] cdrom: sr0: mrw address space DMA selected
[ 6.123057] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 6.135242] ISOFS: changing to secondary root
[ 16.311667] aufs test_add:261:mount[593]: uid/gid/perm /pup_ro2 0/0/0755, 0/0/01777
>[ 53.021330] udev[6062]: starting version 167
[ 54.064751] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 54.064783] ACPI: Power Button [PWRB]
[ 54.065014] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 54.065030] ACPI: Sleep Button [FUTS]
[ 54.065273] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 54.065284] ACPI: Power Button [PWRF]
[ 56.441228] parport_pc 00:09: reported by Plug and Play ACPI
[ 56.441362] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 56.781062] ppdev: user-space parallel port driver
[ 57.003310] thermal LNXTHERM:00: registered as thermal_zone0
[ 57.003324] ACPI: Thermal Zone [THRM] (50 C)
[ 57.036084] ACPI: Fan [FAN] (on)
[ 59.428582] Linux agpgart interface v0.103
[ 59.560258] agpgart-sis 0000:00:00.0: SiS chipset [1039/0651]
[ 59.885293] agpgart-sis 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[ 59.885467] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 60.821492] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x10c0
[ 61.349651] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 61.349822] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 61.349970] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 61.894514] sis900.c: v1.08.10 Apr. 2 2006
[ 61.896504] sis900 0000:00:04.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 61.898070] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
[ 61.911912] 0000:00:04.0: Using transceiver found at address 1 as default
[ 62.356385] eth0: SiS 900 PCI Fast Ethernet at 0xe800, IRQ 19, 00:11:09:67:05:b0
[ 62.531736] cfg80211: Calling CRDA to update world regulatory domain
[ 62.733019] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 63.048668] ath9k 0000:00:07.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 63.945558] Adding 1349628k swap on /dev/sda2. Priority:-1 extents:1 across:1349628k
[ 65.045183] ath: EEPROM regdomain: 0x809c
[ 65.045195] ath: EEPROM indicates we should expect a country code
[ 65.045204] ath: doing EEPROM country->regdmn map search
[ 65.045210] ath: country maps to regdmn code: 0x52
[ 65.045217] ath: Country alpha2 being used: CN
[ 65.045222] ath: Regpair used: 0x52
[ 65.181844] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 65.182965] Registered led device: ath9k-phy0
[ 65.182981] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xf8740000, irq=18
[ 65.183556] snd_intel8x0 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 65.560199] intel8x0_measure_ac97_clock: measured 53268 usecs (2563 samples)
[ 65.560211] intel8x0: clocking to 48000
[ 65.961148] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 65.961164] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 66.494670] eth0: Media Link Off
[ 66.827716] eth0: Media Link Off
[ 72.360088] ------------[ cut here ]------------
[ 72.360130] WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0xed/0x16d()
[ 72.360138] Hardware name:
[ 72.360144] NETDEV WATCHDOG: eth0 (sis900): transmit queue 0 timed out
[ 72.360150] Modules linked in: arc4 snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_mpu401 snd_mpu401_uart snd_seq_midi snd_seq_midi_event snd_rawmidi ath9k ath9k_common snd_seq ath9k_hw mac80211 pcspkr snd_seq_device ath snd_timer cfg80211 rfkill sis900 snd sg soundcore i2c_sis96x snd_page_alloc i2c_core shpchp sis_agp agpgart thermal fan ppdev evdev parport_pc parport button processor thermal_sys hwmon fuse aufs squashfs floppy [last unloaded: battery]
[ 72.360264] Pid: 8521, comm: localedef Not tainted 3.2.29 #1
[ 72.360271] Call Trace:
[ 72.360293] [<c102609c>] ? warn_slowpath_common+0x68/0x79
[ 72.360303] [<c12cb1c4>] ? dev_watchdog+0xed/0x16d
[ 72.360311] [<c1026115>] ? warn_slowpath_fmt+0x29/0x2d
[ 72.360320] [<c12cb1c4>] ? dev_watchdog+0xed/0x16d
[ 72.360331] [<c12cb0d7>] ? qdisc_reset+0x2d/0x2d
[ 72.360349] [<c102de1e>] ? run_timer_softirq+0xfb/0x172
[ 72.360358] [<c102a14c>] ? __do_softirq+0x69/0xdf
[ 72.360366] [<c102a0e3>] ? remote_softirq_receive+0x11/0x11
[ 72.360372] <IRQ> [<c102a310>] ? irq_exit+0x32/0x84
[ 72.360390] [<c101445a>] ? smp_apic_timer_interrupt+0x69/0x73
[ 72.360403] [<c132997a>] ? apic_timer_interrupt+0x2a/0x30
[ 72.360411] ---[ end trace 9d894ed2f8598652 ]---
[ 72.360422] eth0: Transmit timeout, status 00000004 00000000
[ 72.841503] eth0: Media Link On 100mbps full-duplex
[ 112.763319] usb 1-5: USB disconnect, device number 2
[ 113.000083] usb 1-5: new high-speed USB device number 3 using ehci_hcd
[ 113.124200] usb 1-5: New USB device found, idVendor=0781, idProduct=5567
[ 113.124209] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 113.124218] usb 1-5: Product: Cruzer Blade
[ 113.124223] usb 1-5: Manufacturer: SanDisk
[ 113.124229] usb 1-5: SerialNumber: 4528821DAA5369AA
[ 113.128405] usb-storage: device found at 3
[ 113.128450] scsi3 : usb-storage 1-5:1.0
[ 113.128589] usb-storage: waiting for device to settle before scanning
[ 113.947191] eth0: Media Link Off
[ 114.131080] scsi 3:0:0:0: Direct-Access SanDisk Cruzer Blade 8.02 PQ: 0 ANSI: 0 CCS
[ 114.135763] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 114.135881] sd 3:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB)
[ 114.136500] sd 3:0:0:0: [sdb] Write Protect is off
[ 114.136512] sd 3:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 114.137653] sd 3:0:0:0: [sdb] No Caching mode page present
[ 114.137663] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 114.143246] sd 3:0:0:0: [sdb] No Caching mode page present
[ 114.143258] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 114.144655] usb-storage: device scan complete
[ 114.145385] sdb: sdb1
[ 114.148986] sd 3:0:0:0: [sdb] No Caching mode page present
[ 114.148999] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 114.149010] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 266.499100] ath: Failed to stop TX DMA, queues=0x001!
[ 266.513031] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 266.513042] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 266.592290] ath: Failed to stop TX DMA, queues=0x001!
[ 266.606190] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 266.606202] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 266.682327] ath: Failed to stop TX DMA, queues=0x001!
[ 266.696236] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 266.696247] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 266.772252] ath: Failed to stop TX DMA, queues=0x001!
[ 266.786208] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 266.786219] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 266.862236] ath: Failed to stop TX DMA, queues=0x001!
[ 266.876120] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 266.876131] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 266.952237] ath: Failed to stop TX DMA, queues=0x001!
[ 266.966105] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 266.966116] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 267.042300] ath: Failed to stop TX DMA, queues=0x001!
[ 267.056208] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 267.056218] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 267.132241] ath: Failed to stop TX DMA, queues=0x001!
[ 267.146120] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 267.146129] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 267.222250] ath: Failed to stop TX DMA, queues=0x001!
[ 267.236119] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 267.236131] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 267.312242] ath: Failed to stop TX DMA, queues=0x001!
[ 267.326144] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 267.326156] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 267.402448] ath: Failed to stop TX DMA, queues=0x001!
[ 267.416361] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 267.416371] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 267.450863] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 267.450877] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 268.635586] ath: Failed to stop TX DMA, queues=0x001!
[ 268.649468] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 268.649479] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 268.725580] ath: Failed to stop TX DMA, queues=0x001!
[ 268.739467] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 268.739478] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 268.815594] ath: Failed to stop TX DMA, queues=0x001!
[ 268.829481] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 268.829492] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 268.905576] ath: Failed to stop TX DMA, queues=0x001!
[ 268.919534] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 268.919546] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 268.995603] ath: Failed to stop TX DMA, queues=0x001!
[ 269.009494] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 269.009505] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.085605] ath: Failed to stop TX DMA, queues=0x001!
[ 269.099510] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 269.099520] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.175574] ath: Failed to stop TX DMA, queues=0x001!
[ 269.189453] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 269.189462] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.265601] ath: Failed to stop TX DMA, queues=0x001!
[ 269.279481] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 269.279492] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.355794] ath: Failed to stop TX DMA, queues=0x001!
[ 269.369717] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 269.369728] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.449087] ath: Failed to stop TX DMA, queues=0x001!
[ 269.463008] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 269.463019] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.542284] ath: Failed to stop TX DMA, queues=0x001!
[ 269.556239] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 269.556250] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 269.581702] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 269.581716] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.312560] ath: Failed to stop TX DMA, queues=0x001!
[ 272.326515] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 272.326526] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.405761] ath: Failed to stop TX DMA, queues=0x001!
[ 272.419683] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 272.419693] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.498946] ath: Failed to stop TX DMA, queues=0x001!
[ 272.512828] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 272.512839] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.588910] ath: Failed to stop TX DMA, queues=0x001!
[ 272.602786] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 272.602796] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.678901] ath: Failed to stop TX DMA, queues=0x001!
[ 272.692772] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 272.692782] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.769965] ath: Failed to stop TX DMA, queues=0x001!
[ 272.783868] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 272.783879] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.862243] ath: Failed to stop TX DMA, queues=0x001!
[ 272.876120] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 272.876131] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 272.952286] ath: Failed to stop TX DMA, queues=0x001!
[ 272.966175] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 272.966186] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.042306] ath: Failed to stop TX DMA, queues=0x001!
[ 273.056221] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 273.056232] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.132245] ath: Failed to stop TX DMA, queues=0x001!
[ 273.146119] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 273.146129] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.222239] ath: Failed to stop TX DMA, queues=0x001!
[ 273.236119] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 273.236129] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.260829] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 273.260842] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.438912] ath: Failed to stop TX DMA, queues=0x001!
[ 274.452819] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 274.452829] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.528912] ath: Failed to stop TX DMA, queues=0x001!
[ 274.542786] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 274.542797] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.618921] ath: Failed to stop TX DMA, queues=0x001!
[ 274.632818] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.632828] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.708901] ath: Failed to stop TX DMA, queues=0x001!
[ 274.722772] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.722783] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.798935] ath: Failed to stop TX DMA, queues=0x001!
[ 274.812828] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.812839] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.888909] ath: Failed to stop TX DMA, queues=0x001!
[ 274.902786] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 274.902797] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.978900] ath: Failed to stop TX DMA, queues=0x001!
[ 274.992772] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.992783] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
op in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 273.056232] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.132245] ath: Failed to stop TX DMA, queues=0x001!
[ 273.146119] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 273.146129] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.222239] ath: Failed to stop TX DMA, queues=0x001!
[ 273.236119] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 273.236129] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 273.260829] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 273.260842] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.438912] ath: Failed to stop TX DMA, queues=0x001!
[ 274.452819] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 274.452829] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.528912] ath: Failed to stop TX DMA, queues=0x001!
[ 274.542786] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 274.542797] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.618921] ath: Failed to stop TX DMA, queues=0x001!
[ 274.632818] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.632828] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.708901] ath: Failed to stop TX DMA, queues=0x001!
[ 274.722772] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.722783] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.798935] ath: Failed to stop TX DMA, queues=0x001!
[ 274.812828] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.812839] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.888909] ath: Failed to stop TX DMA, queues=0x001!
[ 274.902786] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040
[ 274.902797] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 274.978900] ath: Failed to stop TX DMA, queues=0x001!
[ 274.992772] ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00008040
[ 274.992783] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up


any clue? Confused

thanks for your replies Smile
Back to top
View user's profile Send private message 
pemasu


Joined: 08 Jul 2009
Posts: 5459
Location: Finland

PostPosted: Thu 31 Jan 2013, 02:13    Post subject:  

ath9k loads and uses country code CN ie China.
Quote:
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52

And then it fails with negotiation.
Quote:
ath: Failed to stop TX DMA, queues=0x001!
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x00006040

If you are not from China, this might be the problem. Use the link provided by rcrsn51: http://murga-linux.com/puppy/viewtopic.php?p=562965#562965

You probably need to use the manual route for entering your country code.

Use the method provided by that link.
Your country code need to be entered to the config file as numeric value.
Quote:
Once you have installed the ath9k driver dotpet, use Geany to open /root/my-documents/ath9k-country-codes.txt


Find you country code, then calculate the final value and enter it to the config file as was suggested in that link. After that you need to reboot ie you need savefile.
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Fri 01 Feb 2013, 01:38    Post subject:  

Thanks for your answer pemasu.

well i did what you told me, with puppy-es pasaggio and the first time it works fine, the wizard showed my wireless connection, but doesn't connect because there is a problem with the WPA2-PSK encription. Then i'd installed puppy-es pasaggio again (clean start) and i'd reconfigure all the things step by step and now the first problem persist (wizard dont show any wireless connection). I'd tryed with precise puppy too, (fresh start, reconfigure all again and wizard dont show any wireless connection) i'm from Chile and my country use CL...

this is what dmesg show me now Crying or Very sad

Quote:
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ath9k 0000:00:07.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ath9k: DANGER! You're overriding EEPROM-defined regulatory domain.
ath9k: Your card was not certified to operate on the domain you choosed.
ath9k: This might result in a violation of your local regulatory rules.
ath9k: Do not ever do that unless you really know what you do!
ath: EEPROM regdomain: 0x8098
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x5b
ath: Country alpha2 being used: CL
ath: Regpair used: 0x5b
sis900.c: v1.08.10 Apr. 2 2006
phy0: Selected rate control algorithm 'ath9k_rate_control'
Registered led device: ath9k-phy0::radio
Registered led device: ath9k-phy0::assoc
Registered led device: ath9k-phy0::tx
Registered led device: ath9k-phy0::rx
phy0: Atheros AR9287 Rev:2 mem=0xf8480000, irq=18
cfg80211: Calling CRDA for country: CL
sis900 0000:00:04.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xe800, IRQ 19, 00:11:09:67:05:b0
Intel ICH 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
intel8x0_measure_ac97_clock: measured 53655 usecs (2581 samples)
intel8x0: clocking to 48000
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.

Last edited by occiso on Fri 01 Feb 2013, 15:16; edited 1 time in total
Back to top
View user's profile Send private message 
pemasu


Joined: 08 Jul 2009
Posts: 5459
Location: Finland

PostPosted: Fri 01 Feb 2013, 10:58    Post subject:  

ath9k loads now ok. It complains about your manual country code setting but seems to initialize the wireless chip.

I dont have a clue what to do next....except test the connection without wireless encryption...as test only. Some drivers have problems with certain encryption...but I am not expert with encryption problems.
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Fri 01 Feb 2013, 15:07    Post subject:  

thanks anyway for your time man.

Today, when i turned on this pc, and opened the wizard, it show me now my wireless connection but there is a WPA2-PSK encription issue I thought. Then i've rebooted the pc and opened the wizard again and there is no wireless connection available jajaja Confused

then i do what you suggest, i'd turned off the wireless security of my router, reboot it and rebooted my pc... then i ran the scan for wireless connection, connect to it, and the wizard fails again (with no encription at all).


i'm about to give up, but i'm gonna still asking in the spanish forum for some solution, maybe i'm not to far away to solve it.

anyway, when the wizard show me my wireless connection (when i turned on the pc the first time today), show me this log text:


Quote:
Information about this interface:
Interface: wlan0 Driver: ath9k Bus: pci MacAddress: 90:F6:52:F3:03:69
Description: Support for Atheros 802.11n wireless LAN cards.

STEP1a: ifconfig wlan0 up
STEP1b: iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: B0:48:7A:97:58:30
Channel:2
Frequency:2.417 GHz (Channel 2)
Quality=70/70 Signal level=-36 dBm
Encryption key:on
ESSID:"wireless"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=0000000ffc972d80
Extra: Last beacon: 772ms ago
IE: Unknown: 0008776972656C657373
IE: Unknown: 010882848B960C121824
IE: Unknown: 030102
IE: Unknown: 050400010000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: Unknown: 32043048606C
IE: Unknown: DD180050F2020101860003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C334E111BFF00000000000000000000000000000000000000000000
IE: Unknown: 2D1A4E111BFF00000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C34020D0A00000000000000000000000000000000000000
IE: Unknown: 3D16020D0A00000000000000000000000000000000000000
IE: Unknown: DD0900037F01010000FF7F
IE: Unknown: DD0A00037F04010000004000
IE: Unknown: DD0E0050F204104A0001101044000102
STEP1c: ifconfig wlan0 down
STEP2: iwconfig wlan0 mode managed
STEP3: iwconfig wlan0 channel 2
STEP4: iwconfig wlan0 essid "wireless"
STEP5a: ifconfig wlan0 up
STEP5b: wpa_supplicant -B -Dwext -iwlan0 -c"/etc/simple_network_setup/wpa_supplicant.conf-wireless-90:F6:52:F3:03:69"
Running: wpa_cli -i wlan0 status
wpa_state=SCANNING

ERROR, TIMEOUT. Have not got an Access Point.
Result of 'iwconfig wlan0':
wlan0 IEEE 802.11bgn ESSID:"wireless"
Mode:Managed Frequency:2.417 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on


STEP5a: ifconfig wlan0 up
STEP5b: wpa_supplicant -B -Dwext -iwlan0 -c"/etc/simple_network_setup/wpa_supplicant.conf-wireless-90:F6:52:F3:03:69"
Running: wpa_cli -i wlan0 status
wpa_state=SCANNING

ERROR, TIMEOUT. Have not got an Access Point.
Result of 'iwconfig wlan0':
wlan0 IEEE 802.11bgn ESSID:"wireless"
Mode:Managed Frequency:2.417 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on


STEP5a: ifconfig wlan0 up
STEP5b: wpa_supplicant -B -Dwext -iwlan0 -c"/etc/simple_network_setup/wpa_supplicant.conf-wireless-90:F6:52:F3:03:69"
Running: wpa_cli -i wlan0 status
wpa_state=ASSOCIATING

ERROR, TIMEOUT. Have not got an Access Point.
Result of 'iwconfig wlan0':
wlan0 IEEE 802.11bgn ESSID:"wireless"
Mode:Managed Frequency:2.417 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on


STEP5a: ifconfig wlan0 up
STEP5b: wpa_supplicant -B -Dwext -iwlan0 -c"/etc/simple_network_setup/wpa_supplicant.conf-wireless-90:F6:52:F3:03:69"

ERROR, TIMEOUT. Have not got an Access Point.
Result of 'iwconfig wlan0':
wlan0 IEEE 802.11bgn ESSID:"wireless"
Mode:Managed Frequency:2.417 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on



*********************************************************
LAST 10 LINES of /var/log/messages:
Dec 31 21:10:45 puppy-es user.info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Dec 31 21:10:45 puppy-es user.warn kernel: nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
Dec 31 21:10:45 puppy-es user.warn kernel: CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
Dec 31 21:10:45 puppy-es user.warn kernel: nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
Dec 31 21:10:45 puppy-es user.warn kernel: sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
Dec 31 21:10:46 puppy-es auth.info login[4684]: root login on 'tty1'
Dec 31 21:10:47 puppy-es user.info kernel: eth0: Media Link Off
Dec 31 21:19:22 puppy-es user.debug kernel: ath9k: Two wiphys trying to scan at the same time
Dec 31 21:20:09 puppy-es user.debug kernel: ath9k: Two wiphys trying to scan at the same time
Dec 31 21:20:32 puppy-es user.debug kernel: ath9k: Two wiphys trying to scan at the same time





then, when i turned off the wireless security of my router and the wizard fails trying to connecting to my wireless connection, without any encription, i ran dmesg and this is what the console show me:


Quote:
ath9k 0000:00:07.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ath9k: DANGER! You're overriding EEPROM-defined regulatory domain.
ath9k: Your card was not certified to operate on the domain you choosed.
ath9k: This might result in a violation of your local regulatory rules.
ath9k: Do not ever do that unless you really know what you do!
ath: EEPROM regdomain: 0x8098
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x5b
ath: Country alpha2 being used: CL
ath: Regpair used: 0x5b
usbcore: registered new interface driver hiddev
input: HOLTEK Wireless USB Device as /devices/pci0000:00/0000:00:03.0/usb2/2-3/2-3:1.0/input/input4
generic-usb 0003:04D9:A06B.0001: input: USB HID v1.10 Keyboard [HOLTEK Wireless USB Device] on usb-0000:00:03.0-3/input0
input: HOLTEK Wireless USB Device as /devices/pci0000:00/0000:00:03.0/usb2/2-3/2-3:1.1/input/input5
generic-usb 0003:04D9:A06B.0002: input,hiddev96: USB HID v1.10 Mouse [HOLTEK Wireless USB Device] on usb-0000:00:03.0-3/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
sis900.c: v1.08.10 Apr. 2 2006
phy0: Selected rate control algorithm 'ath9k_rate_control'
Registered led device: ath9k-phy0::radio
Registered led device: ath9k-phy0::assoc
Registered led device: ath9k-phy0::tx
Registered led device: ath9k-phy0::rx
phy0: Atheros AR9287 Rev:2 mem=0xf83c0000, irq=18
cfg80211: Calling CRDA for country: CL
sis900 0000:00:04.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xe800, IRQ 19, 00:11:09:67:05:b0
Intel ICH 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
intel8x0_measure_ac97_clock: measured 53126 usecs (2555 samples)
intel8x0: clocking to 48000
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
eth0: Media Link On 100mbps full-duplex
wlan0: direct probe to AP b0:48:7a:97:58:30 (try 1)
wlan0: direct probe to AP b0:48:7a:97:58:30 (try 2)
wlan0: direct probe to AP b0:48:7a:97:58:30 (try 3)
wlan0: direct probe to AP b0:48:7a:97:58:30 timed out



Rolling Eyes
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Mon 04 Feb 2013, 16:16    Post subject:  

Hi there.
I have good news about this issue.
When a give up trying with puppy linux, i'd installed windows xp ( Crying or Very sad ) and the problem persist even in xp. So i thought that there is no a puppy problem, so i moved my wireless pci adapter to another pci slot and works fine in xp. So i uninstalled windows and installed puppy Linux instead and now my wireless connection works perfectly with ath9k native driver Cool

I'm happy now, thanks for your answers!!!

cheers Laughing
Back to top
View user's profile Send private message 
pemasu


Joined: 08 Jul 2009
Posts: 5459
Location: Finland

PostPosted: Mon 04 Feb 2013, 16:29    Post subject:  

Happy ending is what we all like. You could add [Solved] to your first post header.
Last edited by pemasu on Mon 04 Feb 2013, 17:56; edited 1 time in total
Back to top
View user's profile Send private message 
occiso


Joined: 29 Jan 2013
Posts: 14
Location: Chile

PostPosted: Mon 04 Feb 2013, 16:43    Post subject:  

yeah, nilson was opened this post so i'll telling him

thanks pemasu!!!
Wink
Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 1 of 1 [14 Posts]  
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » Advanced Topics » Hardware » Networking » Wireless
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.2266s ][ Queries: 12 (0.0042s) ][ GZIP on ]