Puppy Linux Discussion Forum

[peebee]

[James C]

[01micko]

Thanks guys for network_tray reports

There is a bug though if you have 2 wired network interfaces..particularly noticeable if you are connected to the second one, this would have been in the original by Barry (and inherited by rerwin's) anyway. Also, there is a bug if you have a ppp (any kind of modem) interface. though it's not as serious as the 2 eth interface bug. The fix should fix both. On the hunt.

[01micko]

**************

5.4.0.4 is out

See main post

**************

[Billtoo]

I did a manual frugal install to an 8gb SDHC card formatted ext4,
using grub4dos as the bootloader.
VIDEO REPORT: Slacko Puppy, version 5.4.0.4

Chip description:
VGA compatible controller: ATI Technologies Inc Radeon HD 3200 Graphics
Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and
Audio Decoder (rev 04)
Requested by /etc/X11/xorg.conf:
Depth (bits, or planes): 24
Modules requested to be loaded: dbe
Drivers requested to be loaded: fglrx
Probing Xorg startup log file (/var/log/Xorg.0.log):
Driver loaded (and currently in use): fglrx
Loaded modules: amdxmm dbe ddc dri dri2 extmod fb fglrxdrm glesx glx kbd
mouse ramdac record vbe vgahw
Actual rendering on monitor:
Resolution: 1440x900 pixels (380x238 millimeters)
Depth: 24 planes
OpenGL
Vendor Advanced Micro Devices, Inc.
Renderer ATI Radeon HD 3200 Graphics
Version 3.3.11672 Compatibility Profile Context
Direct Rendering Y_es
# glxgears
19584 frames in 5.0 seconds = 3916.722 FPS
19695 frames in 5.0 seconds = 3938.826 FPS
19734 frames in 5.0 seconds = 3946.735 FPS
Computer
Processor 4x AMD Phenom(tm) II X4 810 Processor
Memory 3374MB (198MB used)

I installed kdegames from ppm (the devx wasn't loaded) and the broken
pinboard bug is gone.
I loaded the devx and installed the proprietary ati driver and
compiled a few pets with no problems.
Looks good so far
I'll attach the htop and cmus pets that I made, also made pets of
fox-1.6.47-i686.pet and xfe-1.34-i686.pet but they are too large to attach.

[James C]

Fresh manual frugal install on the Athlon XP box. Everything good so far.

# report-video
VIDEO REPORT: Slacko Puppy, version 5.4.0.4

Chip description:
VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev c1)

Requested by /etc/X11/xorg.conf:
Resolution (widthxheight, in pixels): 1440x900
Depth (bits, or planes): 24
Modules requested to be loaded: dbe

Probing Xorg startup log file (/var/log/Xorg.0.log):
Driver loaded (and currently in use): nouveau
Loaded modules: dbe dri dri2 exa extmod fb glx kbd mouse record shadowfb

Actual rendering on monitor:
Resolution: 1440x900 pixels (380x238 millimeters)
Depth: 24 planes

...the above also recorded in /tmp/report-video
# glxgears
Running synchronized to the vertical refresh. The framerate should be
approximately the same as the monitor refresh rate.
1848 frames in 5.0 seconds = 368.995 FPS
1887 frames in 5.0 seconds = 376.797 FPS
1845 frames in 5.0 seconds = 368.929 FPS
1815 frames in 5.0 seconds = 362.634 FPS
1897 frames in 5.0 seconds = 379.276 FPS
1891 frames in 5.0 seconds = 378.091 FPS
1842 frames in 5.0 seconds = 368.376 FPS

-Computer-
Processor : AMD Athlon(tm) XP 2400+
Memory : 1033MB (214MB used)
Machine Type : Physical machine
Operating System : Puppy Linux
User Name : root (root)
Date/Time : Wed Feb 27 08:53:24 2013
-Display-
Resolution : 1440x900 pixels
OpenGL Renderer : Mesa DRI nv18 x86/MMX+/3DNow!+/SSE
X11 Vendor : The X.Org Foundation
-Audio Devices-
Audio Adapter : VIA8233 - VIA 8235

Looking solid.

[ally]

hey micko

sorry for the delay

vattery works correctly with battery installed but reads 'segmentation fault' when no battery is present (on dock), tested puppy431, slacko 5.3.3, fatdog64-611 and lightouse64-511 and all cope ok with battery removed

without battery no display, "seg fault" shows in terminal

HTH

[Terryphi]

Using savefile from Slacko 5.4 in 5.4.0.4 results in hang during boot.

Ah, I see. Savefile changed from .3fs to .2fs.

[Billtoo]

Manual frugal install to a 2tb usb3.0 hard drive, using grub4dos as
the bootloader.
video-info-glx1.5.1Wed 27 Feb 2013onSlacko Puppy 5.4.0.4 Linux 3.4.17-PAE i686
0.0 VGA compatible controller: nVidia Corporation Device 1082 (rev a1)
oem: NVIDIA
product: GF110 Board - 12630002 Chip Rev
X Server: Xorg Driver: nvidia
X.Org version: 1.12.3
dimensions: 3840x1080 pixels (1027x292 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.4
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce GTX 560 Ti/PCIe/SSE2
OpenGL version string: 4.3.0 NVIDIA 310.32
Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz
Core 0: @1600 1: @1600 2: @1600 3: @1600 4: @1600
5: @1600 6: @1600 7: @1600 MHz
# glxgears
Running synchronized to the vertical refresh. The framerate should be
approximately the same as the monitor refresh rate.
303 frames in 5.0 seconds = 60.501 FPS
301 frames in 5.0 seconds = 60.000 FPS
301 frames in 5.0 seconds = 60.001 FPS
Network controller Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe
Memory 16473MB (297MB used)

I installed the pets that I made earlier + the proprietary Nvidia
driver.
No problems

[ally]

posting from 5404 on lenovo t61, found and loaded everything at startup

installed my normal apps, gweled worked this time (not on 5303)

nice and snappy, testing begins....

[James C]

Manual frugal upgrade from 5.4.0.3 to 5.4.0.4 on an old P4 box. No problems at all.

# report-video
VIDEO REPORT: Slacko Puppy, version 5.4.0.4

Chip description:
VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02)

Requested by /etc/X11/xorg.conf:
Resolution (widthxheight, in pixels): 1024x768
Depth (bits, or planes): 24
Modules requested to be loaded: dbe

Probing Xorg startup log file (/var/log/Xorg.0.log):
Driver loaded (and currently in use): intel
Loaded modules: dbe dri dri2 extmod fb glx kbd mouse record

Actual rendering on monitor:
Resolution: 1024x768 pixels (270x203 millimeters)
Depth: 24 planes

...the above also recorded in /tmp/report-video
# glxgears
Running synchronized to the vertical refresh. The framerate should be
approximately the same as the monitor refresh rate.
368 frames in 5.0 seconds = 73.419 FPS
376 frames in 5.0 seconds = 75.144 FPS
376 frames in 5.0 seconds = 75.143 FPS
376 frames in 5.0 seconds = 75.144 FPS
376 frames in 5.0 seconds = 75.139 FPS
376 frames in 5.0 seconds = 75.148 FPS
376 frames in 5.0 seconds = 75.143 FPS
376 frames in 5.0 seconds = 75.140 FPS

-Computer-
Processor : Intel(R) Pentium(R) 4 CPU 2.80GHz
Memory : 2592MB (241MB used)
Machine Type : Physical machine
Operating System : Puppy Linux
User Name : root (root)
Date/Time : Wed Feb 27 15:04:14 2013
-Display-
Resolution : 1024x768 pixels
OpenGL Renderer : Mesa DRI Intel(R) 865G x86/MMX/SSE2
X11 Vendor : The X.Org Foundation
-Audio Devices-
Audio Adapter : ICH4 - Intel ICH5

[SFR]

Ok, completely fresh install - spent hours installing lots of stuff, making (my usual) system customizations, and......all is ok!

The only problem I had is the same as Ally's, with powerapplet_tray (since 5.4.0.3), but the version fixed by Rodin.s works fine for me:
http://bkhome.org/blog2/?viewDetailed=00107

Thanks & Greetings!

[zigbert]

+ Nice to adjust mouse sensitivity from mouse wizard
+ Firefox I like
+ Multiple soundcard wizard works as expected
+ Default font is crisp and clear
+ This must be the best looking wallpaper I have seen default in any Puppy.

- CD-player gui is crappy - I will look at it


Sigmund

[01micko]

[01micko]

SFR and ally

Thanks for power applet reports. I'm using the default woof version so I'll update it to rodin.s' version.

ally, can you test it?

Also, I have been informed of an issue with vicmz openbox+ pet in PPM. Looking into that.