Hi Volks....
i use slacko 5.5. Hardinfo shows a temperature sensor temp1. I want to display the temp in conky .... but where can i get this temp? acpitemp dont work and i haven't a thermal_zone in /proc/acpi.
But where get the sensor in hardinfo the shown temperature?
can anybody explain this please?
Thx a lot !
Hardinfo sensors temp1 -> where get the sensor the temp.
- HoerMirAuf
- Posts: 255
- Joined: Tue 22 Jan 2008, 12:11
- Location: Würzburg
If you're asking where the temperature sensor is physically located on the board, I think all CPUs are manufactured with a p-n junction diode on the chip that is specifically intended to be used to measure the temperature of the CPU chip itself. However, the motherboard requires circuitry external to the CPU in order to use the diode as a temperature sensor. I think that's how it works. You could probably find out for sure from the website of your CPU's manufacturer. Just download the 5000-page manual for your CPU.
Do you have something in /sys/class/hwmon?
Have you installed lmsensors? Have you ran sensors-detect after installing and configuring lmsensors.
http://www.murga-linux.com/puppy/viewtopic.php?t=57480
http://www.murga-linux.com/puppy/viewtopic.php?t=74702
then read up on running sensors-detect.
Have you installed lmsensors? Have you ran sensors-detect after installing and configuring lmsensors.
http://www.murga-linux.com/puppy/viewtopic.php?t=57480
Get it atlm_sensors-3.1.2.pet
http://www.murga-linux.com/puppy/viewtopic.php?t=74702
then read up on running sensors-detect.
Cputemp will give you a tray icon that can be clicked to
show temp.
http://murga-linux.com/puppy/viewtopic. ... 046#432546
show temp.
http://murga-linux.com/puppy/viewtopic. ... 046#432546
Inspiron 700m, Pent.M 1.6Ghz, 1Gb ram.
Msi Wind U100, N270 1.6>2.0Ghz, 1.5Gb ram.
Eeepc 8g 701, 900Mhz, 1Gb ram.
Full installs
bash-3.00#
/sys/devices/platform/coretemp.0/temp3_input
/sys/devices/platform/coretemp.0/temp3_label
/sys/devices/platform/coretemp.0/temp2_crit_alarm
/sys/devices/platform/coretemp.0/temp2_crit
/sys/devices/platform/coretemp.0/temp3_crit
/sys/devices/platform/coretemp.0/temp3_crit_alarm
/sys/devices/platform/coretemp.0/temp2_max
/sys/devices/platform/coretemp.0/temp3_max
/sys/devices/platform/coretemp.0/temp2_input
/sys/devices/platform/coretemp.0/temp2_label
Code: Select all
find /sys -name "temp*"
/sys/devices/platform/coretemp.0/temp3_label
/sys/devices/platform/coretemp.0/temp2_crit_alarm
/sys/devices/platform/coretemp.0/temp2_crit
/sys/devices/platform/coretemp.0/temp3_crit
/sys/devices/platform/coretemp.0/temp3_crit_alarm
/sys/devices/platform/coretemp.0/temp2_max
/sys/devices/platform/coretemp.0/temp3_max
/sys/devices/platform/coretemp.0/temp2_input
/sys/devices/platform/coretemp.0/temp2_label
«Give me GUI or Death» -- I give you [[Xx]term[inal]] [[Cc]on[s][ole]] .
Macpup user since 2010 on full installations.
People who want problems with Puppy boot frugal :P
Macpup user since 2010 on full installations.
People who want problems with Puppy boot frugal :P
- HoerMirAuf
- Posts: 255
- Joined: Tue 22 Jan 2008, 12:11
- Location: Würzburg
Hi folks ....
thanks so much for your replies an your hints!!:
@Flash ....
thank you for your hint. But i was searching for the file where the temp-data is stored. Sorry, my english isn't very good, i think i haven't good enunciated me.
@rokytnji
thank you too for this hint. It give me some approach. In /sys/class/hwmon is a subfolder hwmon0 with som files in it. But is there the temp-info stored? lm_sensor 3.1.2 can't find any temp sensor. But i searched around an found to modprobe coretemp. After modprobe coretemp there are 4 temperature-sensors in hwmon and in terminal after using command "sensors":
nouveau seems to be the graphiccard temperature
core 0 and core 1 should be the temperature form the both cpu-cores.
What the Physical id0 temp is, i don't know....
After searching further for lm_sensor hwmon and conky... i found out that i can use the hwon temperature direct in conky with:
${hwmon 0 temp 1} for the nouveau temperature
${hwmon 1 temp 2} for the 1st core temperature
${hwmon 1 temp 3} for the 2nd core temperature
@rjbrewer
thank your for your hint ..... you are right, but i want to use conky and dont want further traybuttons
@Karl Godt
cool! That was just what i was looking for. Well i have just found another solution, but your way is good to know!
Thank you all a lot for your help!!!
thanks so much for your replies an your hints!!:
@Flash ....
thank you for your hint. But i was searching for the file where the temp-data is stored. Sorry, my english isn't very good, i think i haven't good enunciated me.
@rokytnji
thank you too for this hint. It give me some approach. In /sys/class/hwmon is a subfolder hwmon0 with som files in it. But is there the temp-info stored? lm_sensor 3.1.2 can't find any temp sensor. But i searched around an found to modprobe coretemp. After modprobe coretemp there are 4 temperature-sensors in hwmon and in terminal after using command "sensors":
Code: Select all
nouveau-pci-0100
Adapter: PCI adapter
temp1: +42.0 C (high = +100.0 C, crit = +110.0 C)
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +49.0 C (high = +87.0 C, crit = +105.0 C)
Core 0: +49.0 C (high = +87.0 C, crit = +105.0 C)
Core 1: +41.0 C (high = +87.0 C, crit = +105.0 C)
core 0 and core 1 should be the temperature form the both cpu-cores.
What the Physical id0 temp is, i don't know....
After searching further for lm_sensor hwmon and conky... i found out that i can use the hwon temperature direct in conky with:
${hwmon 0 temp 1} for the nouveau temperature
${hwmon 1 temp 2} for the 1st core temperature
${hwmon 1 temp 3} for the 2nd core temperature
@rjbrewer
thank your for your hint ..... you are right, but i want to use conky and dont want further traybuttons
@Karl Godt
cool! That was just what i was looking for. Well i have just found another solution, but your way is good to know!
Thank you all a lot for your help!!!