Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Wed 20 Aug 2014, 05:05
All times are UTC - 4
 Forum index » House Training » Beginners Help ( Start Here)
messed up network adapter after slacko boot
Moderators: Flash, Ian, JohnMurga
Post_new_topic   Reply_to_topic View_previous_topic :: View_next_topic
Page 1 of 1 Posts_count  
Author Message
noob_g

Joined: 13 Mar 2013
Posts: 4

PostPosted: Wed 13 Mar 2013, 11:03    Post_subject:  messed up network adapter after slacko boot  

Hi,

I am a newbie to puppy.
Just few hours ago, i installed the slacko version 5.5 into a usb stick, and boot it up on my main desktop installed with windows 7.
Everything works smoothly until i switch back to windows 7 to find my network adapter is screwed. Ethernet cable is plugged in but there isn't any network access.

Nothing wrong with my router since all other computer can connect to the net.
I have used restore point, still no luck..
I have even reinstalled windows 7 back to my desktop..so far no luck..
I even load default setting on the bios, and still no luck..

Any solution??

any help is greatly appreciated!
Back to top
View user's profile Send_private_message 
hal8000

Joined: 05 Mar 2013
Posts: 6

PostPosted: Wed 13 Mar 2013, 16:33    Post_subject:  

You should always quote some hardware, whethere its a separate ethernet card or a LAN port on your motherboard.

From puppy USB open the console and post output of


lspci | grep -i eth

The above command will give the ethernet chipset.

However this may work as a solution.
After using puppy from USB shutdown the computer and unpug from electric supply (or use the main switch on the PSU).

Wait 30 seconds and reboot.
The cold boot will restore your hardware to a default state and I am pretty sure you will have connectivity again.
Going through BIOS may work but you would have to disable onboard LAN , rebbot enable onboard LAN.

I had same problem with a Gigabyte Motherboard GA-P55A-UD3 with builtin ethernet (RTL8111). This dual booted linux and windows 7 and I occasionally had no internet connectivity. The LAN port would lock up
and not work in windows unless I did a cold boot.

This was using linux with an earlier 2.6 36 kernel, and since most mainstream distros now use a later kernel problem has disappeared.

Windows restore points seldom solve anything, I turn them off as they waste HDD space. You can always fix anything in windows from linux
anyway.
Hope that helps.
Back to top
View user's profile Send_private_message 
rcrsn51


Joined: 05 Sep 2006
Posts: 9027
Location: Stratford, Ontario

PostPosted: Wed 13 Mar 2013, 16:43    Post_subject:  

Reboot your router.
Back to top
View user's profile Send_private_message 
noob_g

Joined: 13 Mar 2013
Posts: 4

PostPosted: Wed 13 Mar 2013, 18:42    Post_subject:  

WoW cold boot solve the problem!!!!!!!! hurray! thanks hal8000!

I got a gigabyte motherboard as well. It's H61m-usb3-b3. The network adapter is atheros 8151 onboard the motherboard.

This is just a precaution before i boot puppy up again on my laptop, is this problem applicable to laptop as well?
if yes, what is the cold boot for laptop?remove battery and ac??

@rcrsn51, rebooting router wouldn't solve the problem. i tried that last night..
Back to top
View user's profile Send_private_message 
kickstart


Joined: 09 Mar 2011
Posts: 86

PostPosted: Thu 14 Mar 2013, 13:51    Post_subject:  

I get something similar if I use Lucid 5.28 on my desktop computer. Next time Windows XP is booted, it will connect to the wireless LAN but not to the WAN so no internet connectivity. Even a cold boot doesn't fix it. Simply removing the USB wireless adapter for a few seconds then plugging it back in clears the problem. Weird!
Back to top
View user's profile Send_private_message 
Display_posts:   Sort by:   
Page 1 of 1 Posts_count  
Post_new_topic   Reply_to_topic View_previous_topic :: View_next_topic
 Forum index » House Training » Beginners Help ( Start Here)
Jump to:  

Rules_post_cannot
Rules_reply_cannot
Rules_edit_cannot
Rules_delete_cannot
Rules_vote_cannot
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0541s ][ Queries: 12 (0.0108s) ][ GZIP on ]