Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Sat 25 Oct 2014, 01:45
All times are UTC - 4
 Forum index » Advanced Topics » Hardware » Networking » Wireless
[SOLVED] Network scan error with AR9285
Post_new_topic   Reply_to_topic View_previous_topic :: View_next_topic
Page 1 of 1 Posts_count  
Author Message
olaf

Joined: 16 Aug 2010
Posts: 9

PostPosted: Sat 16 Feb 2013, 09:44    Post_subject:  [SOLVED] Network scan error with AR9285
Sub_title: ifconfig: SIOCSIFFLAGS: Operation not possible due to RF-kill
 

Hi!

Precise 5.4.3 network scan with AR9285 gives me an error:

Code:

Error!
Failed to raise interface Wlan0.
Failed command was: ifconfig wlan0 up
Error returned was:
ifconfig: SIOCSIFFLAGS: Operation not possible due to RF-kill


Puppy network wizard detects the AR9285 as wlan0 with ath9k.

"rfkill list" gives:
Code:

0:  hp-wifi: wlan
                  Soft blockes: yes
                  Hard blocked: no
1:  hp-bluetooth: bluetooth
                  Soft blockes: yes
                  Hard blocked: no
2:  phy0: wlan
                  Soft blockes: no
                  Hard blocked: yes


The Notebook from HP has a f12/wifi button. It has effect on the "hard blocked" entries of points 0 and 1, but not 2.

Is there any solution?

Bye
Olaf

Edited_time_total
Back to top
View user's profile Send_private_message 
pemasu


Joined: 08 Jul 2009
Posts: 5463
Location: Finland

PostPosted: Sat 16 Feb 2013, 11:12    Post_subject:  

rfkill unblock all
or
rfkill unblock wlan

commands given in console.
Back to top
View user's profile Send_private_message 
olaf

Joined: 16 Aug 2010
Posts: 9

PostPosted: Sat 16 Feb 2013, 11:34    Post_subject:  

I have tried both a few hours before; have found that in an other forum-topic. Nothing changed.

I have boot Suse SLED, WLAN works: the f12 key has the correct function (wireless on/off), the Light/LED on the f12-button changed from red to blue, then it works.
But when I boot the Notebook (HP 635), the LED is always red, and change to blue when Suse is bootet.

I think puppy does not work correct with the f12-key.
Back to top
View user's profile Send_private_message 
olaf

Joined: 16 Aug 2010
Posts: 9

PostPosted: Sat 16 Feb 2013, 11:54    Post_subject:  

Found the solution (hope so...):

Bios -> System Configuration -> Action Keys Mode -> change from "Enabled" to "Disabled" -> save -> boot puppy -> press fn+F12 -> Wireless Wizard -> scan -> .... it works!

This changed the way of using the F-keys from directly press F1/F12 to "fn + F1/F12".
I do not know why. Perhaps someone has the same problem and found this topic.

Bye
Olaf
Back to top
View user's profile Send_private_message 
audith

Joined: 23 Mar 2013
Posts: 2

PostPosted: Sat 23 Mar 2013, 07:26    Post_subject: same probel
Sub_title: wifi still not activated
 

Sad
it not work with hp pavilion g6 2301AX

even change the bios settings

the fn+f12 not work
Back to top
View user's profile Send_private_message 
darkcity


Joined: 23 May 2010
Posts: 2462
Location: near here

PostPosted: Sat 23 Mar 2013, 20:43    Post_subject: Re: same probel
Sub_title: wifi still not activated
 

audith wrote:
Sad
it not work with hp pavilion g6 2301AX

even change the bios settings

the fn+f12 not work


Hi audith

Welcome to the forum. Now this thread has been marked solved by the OP I recommend you start a new thread. Try to include as much information as possible, for example-

* which puppy version you are using
* what hardware you have - especially wifi chipset
* what procedures you have carried out already to attempt connection

you can get detail hardware info by going to
PuppyMenu > System > HardInfo

Network device will probably be under Devices > PCI Devices
Twisted Evil

_________________
helping Wiki for help | IF SendSpace link = "dead" THEN PM me ("up file to http://meownplanet.net/")
Back to top
View user's profile Send_private_message Visit_website 
audith

Joined: 23 Mar 2013
Posts: 2

PostPosted: Tue 02 Apr 2013, 12:50    Post_subject:    

puppy version
Slacko Puppy, version 5.5

i have tried bios change, while going boot through use rfkill command it shows

0: hp-wifi: wlan
Soft blockes: no
Hard blocked: no
1: hp-bluetooth: bluetooth
Soft blockes: no
Hard blocked: no


still i am unable to activate the wifi interface



WIFI ADAPTER
Ralink RT3290 802.11bgn Wi-Fi Adapter


using network connection wizard
Back to top
View user's profile Send_private_message 
Display_posts:   Sort by:   
Page 1 of 1 Posts_count  
Post_new_topic   Reply_to_topic View_previous_topic :: View_next_topic
 Forum index » Advanced Topics » Hardware » Networking » Wireless
Jump to:  

Rules_post_cannot
Rules_reply_cannot
Rules_edit_cannot
Rules_delete_cannot
Rules_vote_cannot
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0549s ][ Queries: 12 (0.0040s) ][ GZIP on ]