(OLD) (ARCHIVED) Puppy Linux Discussion Forum

[peebee]

[zagreb999]

SEE screenshot

it is from 2020

[zagreb999]

i forgot to inform

i think seamonkey is RE-MADE
as okular which has only 23 mb
slitaz has kde libs with only
22 mb

[fredx181]

@zagreb999

[peebee]

Slackware Current has:
- added PAM
- updated icu4c to version 67.1

ebace8b96f862afdcd500b8dce297d40 LxPupSc-20.01+7PAM_ICU+-T-k64.iso

{delta from +0}

has these changes for testing

also.....
Kernel Release: 5.6.14-lxpup64
Build Date: Wed May 20 09:26:57 BST 2020

Needs firmware (e.g. in fdrv)

From Here

[Marv]

All good here so far running +7PAM on my usual i5 based hardware (the Fujitsu S761 laptops). Installed first as pristine, then as an update to my +6 install using the stock +7 kernel and then swapping in the 5.6.14 kernel. All the usual checks on each look ok, currently using the update from +6 with the 5.6.14 kernel swapped in. I know naught about PAM at this point, this is just regular daily use with sylpheed, Slimjet 26.0.3.0, geany, etc.

Cheers,

[peebee]

Kernel Release: 5.6.15-lxpup64
Build Date: Wed May 27 17:54:11 BST 2020

Needs firmware (e.g. in fdrv)

From Here

[Marv]

A couple of days now running Kernel Release: 5.6.15-lxpup64 in LxPupSc +7PAM and LxPupSc64 +4 on the i5 based Fujitsu S761. Boot and all the usual tests ok on both pups, as is normal daily use. Using mistfires xorg-autoconf v3.0 in both.

[peebee]

Kernel Release: 5.7.0-lxpup64
Build Date: Mon Jun 1 07:31:22 BST 2020

Needs firmware (e.g. in fdrv)

From Here

[Marv]

Kernel Release: 5.7.0-lxpup64 up and running in LxPupSc +7PAM, both as a RAMboot and swapped into my +7 savefile version. Boot and dmesg checks clean in both cases, glxgears video FPS good at 7000 FPS, mitigation unchanged from that seen with the 5.6.xx kernels on this 2nd gen i5 hardware (Fujitsu S761). RAM and CPU % at idle remain good. I rechecked more methodically (using the RAMboot) what I had noted previously and indeed the default soothe overall theme uses measurably more CPU at idle than the xfce orange I usually run, 5% vs 1% reported by LxTask. No change going from the default simple windows theme to the W8 amber I run in my custom version. Of interest only to me, but I've noted it for long enough so I finally chased it. Sound fine in both RAMboot and savefile boot, no multimedia checks run yet in either. Your slimjet_lxsc_spot_26.0.10.0.sfs continues to be spot on I did roll a 64b version SFS of 26.0.10.0 and it is just fine in both LxPupSc64 and FossaPup64.

Update 06 June: Also swapped the 5.7.0 kernel into my LxPupSc64 20.01 +6 install on this hardware. Normal boot, good test results, and no problems noted there in a days normal use

Thanks,

[grimoire]

is this pae boot ready?

[peebee]

Kernel Release: 5.7.1-lxpup64
Build Date: Sun Jun 7 17:56:03 BST 2020

Needs firmware (e.g. in fdrv)

From Here

[Marv]

Kernel Release: 5.7.1-lxpup64 swapped into both my current LxPupSc installs, 32b and 64b, on the Fujitsu laptop in my posts above. Boot, the usual checks, and normal use all good on both pups. Using the 64b at the moment, posting from Slimjet 26.0.10.0 loaded from SFS.

Cheers,

[peebee]

Kernel Release: 5.7.2-lxpup64
Build Date: Thu Jun 11 11:38:25 BST 2020

Needs firmware (e.g. in fdrv)

From Here

[peebee]

New baseline 20.06+0 is available - see post #1

delta from 20.01+0