slacko-700 rc3
Update for my wifi issue.
Cuts off and on slow speed.
First, thank you 01micko for looking at possible causes in Slacko 6.9.9.9!!!
Also, others for suggestions!!
I will call this issue not a Slacko 6.9.9.9 specific problem.
This is wifi and a lot of things can affect wifi.
What has helped and made it usable:
Updated firmware/driver for the RTL8821AE 802.11ac PCIe Wireless Network Adapter.
Update to dhcpd
Using a newer Linux kernel.
Moving my wifi router to a different location.
Changing the transmit channel on the wifi router to a set channel, not auto.(I think this fixed the cuts off and on)
Applying wifi router firmware update.
Not using the internet for a few minutes after bootup, to let every possible function get fully loaded.
It seems to get better the longer I use it.
Other factors that could possibly be contributing to this.
My service is cable internet. It changes as people get on and off my section of the cable. Normal for cable internet. Band width gets split between the users that are connected.
Running Slacko from a frugal install on a USB portable hard drive.
Puppy thinks it is a ata hard drive, so the save is directly accessed and read and written to all the time. Pupmode=12.
I know you can get it to run in pupmode=13, but I am testing like a new user, that is only going to use what got initially setup by Puppy.
Using Grub4dos boot loader and it put pmedia=atahd in the menu entry.
Just some info for you 01micko, so you know your efforts were not lost!!!!!!!
Cuts off and on slow speed.
First, thank you 01micko for looking at possible causes in Slacko 6.9.9.9!!!
Also, others for suggestions!!
I will call this issue not a Slacko 6.9.9.9 specific problem.
This is wifi and a lot of things can affect wifi.
What has helped and made it usable:
Updated firmware/driver for the RTL8821AE 802.11ac PCIe Wireless Network Adapter.
Update to dhcpd
Using a newer Linux kernel.
Moving my wifi router to a different location.
Changing the transmit channel on the wifi router to a set channel, not auto.(I think this fixed the cuts off and on)
Applying wifi router firmware update.
Not using the internet for a few minutes after bootup, to let every possible function get fully loaded.
It seems to get better the longer I use it.
Other factors that could possibly be contributing to this.
My service is cable internet. It changes as people get on and off my section of the cable. Normal for cable internet. Band width gets split between the users that are connected.
Running Slacko from a frugal install on a USB portable hard drive.
Puppy thinks it is a ata hard drive, so the save is directly accessed and read and written to all the time. Pupmode=12.
I know you can get it to run in pupmode=13, but I am testing like a new user, that is only going to use what got initially setup by Puppy.
Using Grub4dos boot loader and it put pmedia=atahd in the menu entry.
Just some info for you 01micko, so you know your efforts were not lost!!!!!!!
Last edited by bigpup on Tue 11 Jul 2017, 22:28, edited 4 times in total.
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
I built a new Slacko64-6.9.9.9 which I'm using with my imac:
# inxi -b
System: Host: puppypc24422 Kernel: 4.4.76 x86_64 (64 bit) Desktop: JWM 2.3.2 Distro: Slacko64 Puppy 6.9.9.9
Machine: Device: desktop System: Apple product: iMac8 1 v: 1.0 serial: W8811GXLZE2
Mobo: Apple model: Mac-F226BEC8 v: PVT serial: 1
BIOS: Apple v: IM81.88Z.00C1.B00.0802091538 date: 02/09/08
CPU: Dual core Intel Core2 Duo E8135 (-MCP-) speed/max: 1600/2400 MHz
Graphics: Card: Advanced Micro Devices [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT]
Display Server: X.org 1.18.3 driver: radeon tty size: 124x33 Advanced Data: N/A for root
Network: Card-1: Broadcom Limited BCM4321 802.11a/b/g/n driver: b43-pci-bridge
Card-2: Marvell 88E8058 PCI-E Gigabit Ethernet Controller driver: sky2
Drives: HDD Total Size: 250.1GB (3.0% used)
Info: Processes: 163 Uptime: 3:10 Memory: 261.2/3934.8MB Client: Shell (bash) inxi: 2.3.8
#
video-info-glx 1.5.3 Wed 5 Jul 2017 on Slacko64 Puppy 6.9.9.9 Linux 4.4.76 x86_64
0.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT]
X Server: Xorg Driver: radeon
X.Org version: 1.18.3
dimensions: 1680x1050 pixels (444x277 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: X.Org
OpenGL renderer string: Gallium 0.4 on AMD RV610 (DRM 2.43.0, LLVM 3.8.0)
OpenGL core profile version string: 3.3 (Core Profile) Mesa 11.2.2
Intel(R) Core(TM)2 Duo CPU E8135 @ 2.40GHz
Core 0: @800 1: @800 MHz
This isn't built with the newest woof-CE but a slightly older version (which works fine) the newest version builds okay
but on first boot it doesn't get to the desktop,running xorgwizard doesn't help.
This is booting from the live DVD with a savefile on the hard drive.
Thanks.
EDIT: I downloaded guvcview-1.7.1-x86_64-2.txz from the Fatdog 710 packages and installed it, it needed portaudio from PPM added but now works fine with the built-in iSight camera in this imac.
EDIT2: I did a slacko-6.9.9.9 build with the latest rationalise branch of woof-CE and it's working well (screenshot2)
# inxi -b
System: Host: puppypc24422 Kernel: 4.4.76 x86_64 (64 bit) Desktop: JWM 2.3.2 Distro: Slacko64 Puppy 6.9.9.9
Machine: Device: desktop System: Apple product: iMac8 1 v: 1.0 serial: W8811GXLZE2
Mobo: Apple model: Mac-F226BEC8 v: PVT serial: 1
BIOS: Apple v: IM81.88Z.00C1.B00.0802091538 date: 02/09/08
CPU: Dual core Intel Core2 Duo E8135 (-MCP-) speed/max: 1600/2400 MHz
Graphics: Card: Advanced Micro Devices [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT]
Display Server: X.org 1.18.3 driver: radeon tty size: 124x33 Advanced Data: N/A for root
Network: Card-1: Broadcom Limited BCM4321 802.11a/b/g/n driver: b43-pci-bridge
Card-2: Marvell 88E8058 PCI-E Gigabit Ethernet Controller driver: sky2
Drives: HDD Total Size: 250.1GB (3.0% used)
Info: Processes: 163 Uptime: 3:10 Memory: 261.2/3934.8MB Client: Shell (bash) inxi: 2.3.8
#
video-info-glx 1.5.3 Wed 5 Jul 2017 on Slacko64 Puppy 6.9.9.9 Linux 4.4.76 x86_64
0.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT]
X Server: Xorg Driver: radeon
X.Org version: 1.18.3
dimensions: 1680x1050 pixels (444x277 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: X.Org
OpenGL renderer string: Gallium 0.4 on AMD RV610 (DRM 2.43.0, LLVM 3.8.0)
OpenGL core profile version string: 3.3 (Core Profile) Mesa 11.2.2
Intel(R) Core(TM)2 Duo CPU E8135 @ 2.40GHz
Core 0: @800 1: @800 MHz
This isn't built with the newest woof-CE but a slightly older version (which works fine) the newest version builds okay
but on first boot it doesn't get to the desktop,running xorgwizard doesn't help.
This is booting from the live DVD with a savefile on the hard drive.
Thanks.
EDIT: I downloaded guvcview-1.7.1-x86_64-2.txz from the Fatdog 710 packages and installed it, it needed portaudio from PPM added but now works fine with the built-in iSight camera in this imac.
EDIT2: I did a slacko-6.9.9.9 build with the latest rationalise branch of woof-CE and it's working well (screenshot2)
- Attachments
-
- screenshot2.jpg
- (39.13 KiB) Downloaded 1348 times
-
- screenshot.jpg
- (80.35 KiB) Downloaded 1522 times
- mister_electronico
- Posts: 969
- Joined: Sun 20 Jan 2008, 20:20
- Location: Asturias_ España
- Contact:
low resolution Radeon 3000
The maximum resolution that I get with my card :
Advanced Micro Devices, Inc. [AMD/ATI] RS780L [Radeon 3000] is 800 X 600 .
Any idea to get more resolution?
Thanks
Advanced Micro Devices, Inc. [AMD/ATI] RS780L [Radeon 3000] is 800 X 600 .
Any idea to get more resolution?
Thanks
Re: low resolution Radeon 3000
Himister_electronico wrote:The maximum resolution that I get with my card :
Advanced Micro Devices, Inc. [AMD/ATI] RS780L [Radeon 3000] is 800 X 600 .
Any idea to get more resolution?
Thanks
You can exit to the prompt and run xorgwizard, it produces a menu with
4 options.
1.Set video driver.. (specify radeon)
2.Set screen resolution.. (specify your desired screen resolution)
3.Set color bith depth.. (16 or 24)
Then highlight Done and press enter.
Now xwin to get back to the desktop.
It works for me.
- mister_electronico
- Posts: 969
- Joined: Sun 20 Jan 2008, 20:20
- Location: Asturias_ España
- Contact:
Many thanks.
Many thanks Billtoo, everything now works perfectly, and the graphics card function to 1920x1080.
Thanks... see you
Thanks... see you
New 6.9.9.9 build booting from DVD with a savefile on the usb SSD (has no
hard drive)
# inxi -b
System: Host: puppypc11730 Kernel: 4.9.36-pae i686 (32 bit) Desktop: JWM 2.3.2 Distro: Slacko Puppy 6.9.9.9
Machine: Device: desktop System: ACER product: Aspire M5620 v: R01-A4 serial: PTS860X0348050CF642700
Mobo: ACER model: G33T-AM v: 1.0 serial: 00000000 BIOS: American Megatrends v: R01-A4 date: 12/19/2007
CPU: Quad core Intel Core2 Quad Q6600 (-MCP-) speed/max: 1603/2403 MHz
Graphics: Card: NVIDIA GF108 [GeForce GT 430]
Display Server: X.org 1.18.3 driver: nvidia tty size: 137x34 Advanced Data: N/A for root
Network: Card: Intel 82566DC-2 Gigabit Network Connection driver: e1000e
Drives: HDD Total Size: 126.3GB (3.5% used)
Info: Processes: 189 Uptime: 14 min Memory: 393.9/8096.6MB Client: Shell (bash) inxi: 2.3.8
#
Using a 32" TV as a monitor via hdmi cable.
It's working well,
Thanks.
hard drive)
# inxi -b
System: Host: puppypc11730 Kernel: 4.9.36-pae i686 (32 bit) Desktop: JWM 2.3.2 Distro: Slacko Puppy 6.9.9.9
Machine: Device: desktop System: ACER product: Aspire M5620 v: R01-A4 serial: PTS860X0348050CF642700
Mobo: ACER model: G33T-AM v: 1.0 serial: 00000000 BIOS: American Megatrends v: R01-A4 date: 12/19/2007
CPU: Quad core Intel Core2 Quad Q6600 (-MCP-) speed/max: 1603/2403 MHz
Graphics: Card: NVIDIA GF108 [GeForce GT 430]
Display Server: X.org 1.18.3 driver: nvidia tty size: 137x34 Advanced Data: N/A for root
Network: Card: Intel 82566DC-2 Gigabit Network Connection driver: e1000e
Drives: HDD Total Size: 126.3GB (3.5% used)
Info: Processes: 189 Uptime: 14 min Memory: 393.9/8096.6MB Client: Shell (bash) inxi: 2.3.8
#
Using a 32" TV as a monitor via hdmi cable.
It's working well,
Thanks.
- Attachments
-
- screenshot.jpg
- (83.44 KiB) Downloaded 1170 times
-
- Posts: 1543
- Joined: Mon 22 Feb 2016, 19:43
I feel this is still something to try and troubleshoot.
My WIFI issues.
Can read my post for info on what I have done.
http://www.murga-linux.com/puppy/viewto ... 864#959864
After all the things I have tried, I have only one remaining issue.
Slow connection speeds.
Not that slow, but slower than I get when using other Puppy versions.
I am comparing speed using Xenialpup64 7.0.8.5 K4.9.15 and Slacko64 6.9.9.9 K4.9.30.
Same computer and hardware.
Same network setup settings, using Network Wizard.
In Slacko64 6.9.9.9
Internet speeds are 10% to 15% slower in download speed and 70% slower in upload speed.
The only thing I can think, may be causing this, is something in the Linux kernel, that deals with WIFI.
Some kernel setting not correct.
So far, I have not found anything that is not the same as in Xenialpup64's kernel.
Any ideas??????
My WIFI issues.
Can read my post for info on what I have done.
http://www.murga-linux.com/puppy/viewto ... 864#959864
After all the things I have tried, I have only one remaining issue.
Slow connection speeds.
Not that slow, but slower than I get when using other Puppy versions.
I am comparing speed using Xenialpup64 7.0.8.5 K4.9.15 and Slacko64 6.9.9.9 K4.9.30.
Same computer and hardware.
Same network setup settings, using Network Wizard.
In Slacko64 6.9.9.9
Internet speeds are 10% to 15% slower in download speed and 70% slower in upload speed.
The only thing I can think, may be causing this, is something in the Linux kernel, that deals with WIFI.
Some kernel setting not correct.
So far, I have not found anything that is not the same as in Xenialpup64's kernel.
Any ideas??????
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
Yes, about the same speeds.
USB wifi adapter Netgear WNA1100 using a ath9k_htc driver.
Just seems to act like some setting just not correct or the best.
I tried comparing the linux kernel wifi settings, but that gets a little deep for me and I am not totally sure I am look at the correct stuff.
https://wireless.wiki.kernel.org/
I could go back to trying the 4.9.15 kernel in Slacko64 6.9.9.9, but this is test of what is offered with a normal Slacko64 6.9.9.9 iso.
USB wifi adapter Netgear WNA1100 using a ath9k_htc driver.
Just seems to act like some setting just not correct or the best.
I tried comparing the linux kernel wifi settings, but that gets a little deep for me and I am not totally sure I am look at the correct stuff.
https://wireless.wiki.kernel.org/
I could go back to trying the 4.9.15 kernel in Slacko64 6.9.9.9, but this is test of what is offered with a normal Slacko64 6.9.9.9 iso.
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
Slacko64 6.9.9.9
I tried to use Getnvidia64 program to make and load The needed Nvidia driver package for my hardware.
http://www.murga-linux.com/puppy/viewtopic.php?t=72405
One problem.
It wanted to see a directory OpenCL in /etc.
This OpenCL directory was missing.
I created one and Getnvidia program worked with no problem.
Now using the Nvidia driver it made.
I tried to use Getnvidia64 program to make and load The needed Nvidia driver package for my hardware.
http://www.murga-linux.com/puppy/viewtopic.php?t=72405
One problem.
It wanted to see a directory OpenCL in /etc.
This OpenCL directory was missing.
I created one and Getnvidia program worked with no problem.
Now using the Nvidia driver it made.
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
I did a new 6.9.9.9 install to a 32gb flash drive.
# inxi -b
System: Host: puppypc23088 Kernel: 4.9.38-pae i686 (32 bit) Desktop: JWM 2.3.2 Distro: Slacko Puppy 6.9.9.9
Machine: Device: desktop System: HP product: 260-p029 serial: CNV6240BWP
Mobo: HP model: 81B4 v: 01 serial: PFPSK0BWJ301LW UEFI [Legacy]: AMI v: F.04 date: 05/10/2016
CPU: Dual core Intel Core i3-6100T (-HT-MCP-) speed/max: 1100/3101 MHz
Graphics: Card: Intel HD Graphics 530
Display Server: X.org 1.18.3 driver: intel tty size: 142x26 Advanced Data: N/A for root
Network: Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Card-2: Realtek RTL8723BE PCIe Wireless Network Adapter driver: rtl8723be
Drives: HDD Total Size: 1032.2GB (0.6% used)
Info: Processes: 191 Uptime: 1:24 Memory: 319.2/3898.0MB Client: Shell (bash) inxi: 2.3.8
#
Works okay so far.
Thanks
# inxi -b
System: Host: puppypc23088 Kernel: 4.9.38-pae i686 (32 bit) Desktop: JWM 2.3.2 Distro: Slacko Puppy 6.9.9.9
Machine: Device: desktop System: HP product: 260-p029 serial: CNV6240BWP
Mobo: HP model: 81B4 v: 01 serial: PFPSK0BWJ301LW UEFI [Legacy]: AMI v: F.04 date: 05/10/2016
CPU: Dual core Intel Core i3-6100T (-HT-MCP-) speed/max: 1100/3101 MHz
Graphics: Card: Intel HD Graphics 530
Display Server: X.org 1.18.3 driver: intel tty size: 142x26 Advanced Data: N/A for root
Network: Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Card-2: Realtek RTL8723BE PCIe Wireless Network Adapter driver: rtl8723be
Drives: HDD Total Size: 1032.2GB (0.6% used)
Info: Processes: 191 Uptime: 1:24 Memory: 319.2/3898.0MB Client: Shell (bash) inxi: 2.3.8
#
Works okay so far.
Thanks
- Attachments
-
- screenshot.jpg
- (93.66 KiB) Downloaded 640 times
New install to Acer laptop:
# inxi -b
System: Host: puppypc4126 Kernel: 4.4.77-pae i686 (32 bit) Desktop: JWM 2.3.2
Distro: Slacko Puppy 6.9.9.9
Machine: Device: laptop System: Acer product: Aspire V5-571P v: V2.17 serial: NXM49AA03531512EC36600
Mobo: Acer model: Aspire V5-571P v: V2.17 serial: NBM491100831501E946600
UEFI [Legacy]: Phoenix v: V2.17 date: 02/27/2013
Battery BAT0: charge: 20.3 Wh 100.0% condition: 20.3/25.0 Wh (81%)
CPU: Dual core Intel Core i3-3227U (-HT-MCP-) speed/max: 800/1901 MHz
Graphics: Card: Intel 3rd Gen Core processor Graphics Controller
Display Server: X.org 1.18.3 driver: intel tty size: 106x29 Advanced Data: N/A for root
Network: Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Card-2: Broadcom Limited BCM43228 802.11a/b/g/n driver: bcma-pci-bridge
Drives: HDD Total Size: 500.1GB (6.3% used)
Info: Processes: 176 Uptime: 2:19 Memory: 274.5/5865.7MB Client: Shell (bash) inxi: 2.3.8
#
The touchscreen is working, no problems so far.
Thanks.
# inxi -b
System: Host: puppypc4126 Kernel: 4.4.77-pae i686 (32 bit) Desktop: JWM 2.3.2
Distro: Slacko Puppy 6.9.9.9
Machine: Device: laptop System: Acer product: Aspire V5-571P v: V2.17 serial: NXM49AA03531512EC36600
Mobo: Acer model: Aspire V5-571P v: V2.17 serial: NBM491100831501E946600
UEFI [Legacy]: Phoenix v: V2.17 date: 02/27/2013
Battery BAT0: charge: 20.3 Wh 100.0% condition: 20.3/25.0 Wh (81%)
CPU: Dual core Intel Core i3-3227U (-HT-MCP-) speed/max: 800/1901 MHz
Graphics: Card: Intel 3rd Gen Core processor Graphics Controller
Display Server: X.org 1.18.3 driver: intel tty size: 106x29 Advanced Data: N/A for root
Network: Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Card-2: Broadcom Limited BCM43228 802.11a/b/g/n driver: bcma-pci-bridge
Drives: HDD Total Size: 500.1GB (6.3% used)
Info: Processes: 176 Uptime: 2:19 Memory: 274.5/5865.7MB Client: Shell (bash) inxi: 2.3.8
#
The touchscreen is working, no problems so far.
Thanks.
- Attachments
-
- screenshot.jpg
- (134.49 KiB) Downloaded 524 times
Don't think only to some devs working Linux
Sorry to underline again what is the main default of Puppy Linux nowadays.
95% of people use wireless at home but oudoor too.
Tablets, smartphones and laptops are the daily equipment used by families.
Don't think only to some devs working Linux with an huge computer linked in the cellar to electrical plug.
All Puppies should be able to run wireless antennas, with the driver included in te ISO
Just an opinion.
Please choose a kernel that can do it !
95% of people use wireless at home but oudoor too.
Tablets, smartphones and laptops are the daily equipment used by families.
Don't think only to some devs working Linux with an huge computer linked in the cellar to electrical plug.
All Puppies should be able to run wireless antennas, with the driver included in te ISO
Just an opinion.
Please choose a kernel that can do it !
- Attachments
-
- tomtom.png
- However, don't use Puppy when driving, only once arrived
- (61.74 KiB) Downloaded 500 times
slack-700
Unable to update When I trying to update from Update Manger - latest from Slackware due to lack of space /temp?. ( Sorry, but there is no enough free space to down load to . Attempted download directory L/tmp. Partition is full. Delete etc.)
My partition is around 25GB. Full Installation of Slack . How to solve it.
My partition is around 25GB. Full Installation of Slack . How to solve it.
Re: slack-700
It sounds like the savefile is full. Are you sure it's a full installation? If it is how much free space do you have free on the 25GB partition?rameshiyer wrote:Unable to update When I trying to update from Update Manger - latest from Slackware due to lack of space /temp?. ( Sorry, but there is no enough free space to down load to . Attempted download directory L/tmp. Partition is full. Delete etc.)
My partition is around 25GB. Full Installation of Slack . How to solve it.
Re: slack-700
Which slacko version are you using?rameshiyer wrote:Unable to update When I trying to update from Update Manger - latest from Slackware due to lack of space /temp?. ( Sorry, but there is no enough free space to down load to . Attempted download directory L/tmp. Partition is full. Delete etc.)
Slacko-6.9.9.9 (this tread) does NOT have an "update manager" application.
Slacko 6.3.x has.
Do you have 6.3.x, 6.9.x or a "hybrid"?
== [url=http://www.catb.org/esr/faqs/smart-questions.html]Here is how to solve your[/url] [url=https://www.chiark.greenend.org.uk/~sgtatham/bugs.html]Linux problems fast[/url] ==
Slack 6.9.9.9
I am using Quirky Slack 6.9.9. I have to check the disk space of the partition. It is around 25GB. I feel it is some technical glitch. I cannot check free disk space as I am away from home.
Just finish installing on a Lenovo X61 also upgraded to a Samsung V-NAND SSD 850 EVO, flashed the BIOS using Middleton upgrade to double the SATA speed from 1.5 GBS to 3.0 GBS
quick before and after
BEFORE
Question: How do you copy text from urvt to a text editor?
quick before and after
Code: Select all
hdparm -tT /dev/sda
AFTER/dev/sda:
Timing buffer-cache reads: 2596 MB in 0.50 seconds = 5229474 kB/s
Timing buffered disk reads: 404 MB in 3.00 seconds = 137878 kB/s
No problems so far, nice work and thank you/dev/sda:
Timing buffer-cache reads: 2690 MB in 0.50 seconds = 5418959 kB/s
Timing buffered disk reads: 793 MB in 3.00 seconds = 270427 kB/s
Question: How do you copy text from urvt to a text editor?
Last edited by solex on Tue 25 Jul 2017, 14:55, edited 1 time in total.
In urxvtQuestion: How do you copy text from urvt to a text editor?
Copy --- highlight by using left mouse button hold and swipe.
paste --- middle mouse button click. If no middle button, click both buttons same time.
Also, in some programs, after you copy in urxvt.
The programs paste command will work to paste in that program.
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)