Booting from floppy
Posted: Fri 02 Feb 2007, 00:36
I have been able to get loaded into puppy w/ (bad video) at 1024 x 768
I have dell latitude LM p133 40m ram 2g HD. This machine needs fb800X600 frame buffered I have a working partition with DSL installation How would I specify video resolution using the new boot floppy.
Any suggestion?
in the boot floppy I see the line for the config.sys:
!SHELL=A:\COMMAND.COM A:\ /E:1024 /F /MSG /P=A:\AUTOEXEC.BAT
If I change it to:
!SHELL=A:\COMMAND.COM A:\ /E:800 /F /MSG /P=A:\AUTOEXEC.BAT
would I be close?
MT
from config.sys
; CONFIG.SYS for wakepup2 (C) 2006, Paul Akterstam ('pakt' on Puppy Linux Forum)
!switches=/e
!files=50
!break=on
!stacks=0,0
lastdrive=Z
buffers=20,0
; load VIDE v2.14 IDE/ATAPI CD-ROM device driver
device=A:\driver\VIDE-CDD.SYS /d:IDE-CD
; enable USB mass storage devices (NEC OHCI/EHCI & Intel UHCI/EHCI USB controllers)
; load Panasonic v2.20 ASPI manager for USB mass storage
; (maps USB mass storage devices to ASPI devices)
device=A:\driver\usb\USBASPI.SYS /v
; load Panasonic v1.00 USB CD-ROM device driver
device=A:\driver\usb\USBCD.SYS /d:USB-CD
; load Adaptec v4.01b ASPI disk driver
; (maps ASPI mass storage devices to DOS drive letters)
device=A:\driver\ASPIDISK.SYS
!SHELL=A:\COMMAND.COM A:\ /E:1024 /F /MSG /P=A:\AUTOEXEC.BAT
I have dell latitude LM p133 40m ram 2g HD. This machine needs fb800X600 frame buffered I have a working partition with DSL installation How would I specify video resolution using the new boot floppy.
Any suggestion?
in the boot floppy I see the line for the config.sys:
!SHELL=A:\COMMAND.COM A:\ /E:1024 /F /MSG /P=A:\AUTOEXEC.BAT
If I change it to:
!SHELL=A:\COMMAND.COM A:\ /E:800 /F /MSG /P=A:\AUTOEXEC.BAT
would I be close?
MT
from config.sys
; CONFIG.SYS for wakepup2 (C) 2006, Paul Akterstam ('pakt' on Puppy Linux Forum)
!switches=/e
!files=50
!break=on
!stacks=0,0
lastdrive=Z
buffers=20,0
; load VIDE v2.14 IDE/ATAPI CD-ROM device driver
device=A:\driver\VIDE-CDD.SYS /d:IDE-CD
; enable USB mass storage devices (NEC OHCI/EHCI & Intel UHCI/EHCI USB controllers)
; load Panasonic v2.20 ASPI manager for USB mass storage
; (maps USB mass storage devices to ASPI devices)
device=A:\driver\usb\USBASPI.SYS /v
; load Panasonic v1.00 USB CD-ROM device driver
device=A:\driver\usb\USBCD.SYS /d:USB-CD
; load Adaptec v4.01b ASPI disk driver
; (maps ASPI mass storage devices to DOS drive letters)
device=A:\driver\ASPIDISK.SYS
!SHELL=A:\COMMAND.COM A:\ /E:1024 /F /MSG /P=A:\AUTOEXEC.BAT