LxPup : a Puppy with LXDE as its desktop environment
LxPup : a Puppy with LXDE as its desktop environment
Manual frugal install to a 16gb flash drive, pc is an Asus Eee PC 701SD.
video-info-glx 1.5.1 Sun 15 Feb 2015 on LxPup 15.02 Linux 3.4.94 i686
2.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
oem: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS
product: Intel(r)915GM/910ML/915MS Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 640x480 pixels (169x126 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) 915GM x86/MMX/SSE2
OpenGL version string: 1.4 Mesa 9.1.7
Intel(R) Celeron(R) M processor 900MHz
Core 0: @Intel(R) 1: @630 MHz
Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01)
I have the netbook connected to an external monitor but can't set it
to a higher resolution, easier to see just the same.
video-info-glx 1.5.1 Sun 15 Feb 2015 on LxPup 15.02 Linux 3.4.94 i686
2.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
oem: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS
product: Intel(r)915GM/910ML/915MS Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 640x480 pixels (169x126 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) 915GM x86/MMX/SSE2
OpenGL version string: 1.4 Mesa 9.1.7
Intel(R) Celeron(R) M processor 900MHz
Core 0: @Intel(R) 1: @630 MHz
Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01)
I have the netbook connected to an external monitor but can't set it
to a higher resolution, easier to see just the same.
- Attachments
-
- Screenshot.jpg
- (76.28 KiB) Downloaded 2960 times
LxPup : a Puppy with LXDE as its desktop environment
I did another install to a 32gb SDHC card:
video-info-glx 1.5.1 Mon 16 Feb 2015 on LxPup 15.02 Linux 3.4.94 i686
2.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
oem: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS
product: Intel(r)915GM/910ML/915MS Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 800x480 pixels (169x126 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) 915GM x86/MMX/SSE2
OpenGL version string: 1.4 Mesa 9.1.7
Intel(R) Celeron(R) M processor 900MHz
Core 0: @Intel(R) 1: @630 MHz
Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01)
Compiled mplayer-checkout-snapshot.tar.bz2 (took an hour and a half),
loaded qt4-4.8.5.sfs (from fatdog64), added scabz's smplayer,smtube,and
cacertificates pets.
Dillo-3.4.0.1 works great on this netbook, firefox not so much.
Connected decent speakers to the headphone jack, this Eee PC 701SD rocks
now
Thanks for LxPup!
EDIT: Typo, should read Dillo-3.0.4.1
video-info-glx 1.5.1 Mon 16 Feb 2015 on LxPup 15.02 Linux 3.4.94 i686
2.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
oem: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS
product: Intel(r)915GM/910ML/915MS Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 800x480 pixels (169x126 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) 915GM x86/MMX/SSE2
OpenGL version string: 1.4 Mesa 9.1.7
Intel(R) Celeron(R) M processor 900MHz
Core 0: @Intel(R) 1: @630 MHz
Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01)
Compiled mplayer-checkout-snapshot.tar.bz2 (took an hour and a half),
loaded qt4-4.8.5.sfs (from fatdog64), added scabz's smplayer,smtube,and
cacertificates pets.
Dillo-3.4.0.1 works great on this netbook, firefox not so much.
Connected decent speakers to the headphone jack, this Eee PC 701SD rocks
now
Thanks for LxPup!
EDIT: Typo, should read Dillo-3.0.4.1
- Attachments
-
- Screenshot.jpg
- (49.52 KiB) Downloaded 1893 times
-
- Screenshot2.jpg
- (46.53 KiB) Downloaded 1693 times
using my lxpup 14.02 save on the newest lxpup, it asked me if i wanted to copy the sfs in the usb stick, so I said yes and then it bugged
I had no firewall set up and custom programs on startup
So I deleted these sfs and the bug was gone.
Can't say more though
I had no firewall set up and custom programs on startup
So I deleted these sfs and the bug was gone.
Can't say more though
Main puppy used : LxPup tahr.
[url=http://www.murga-linux.com/puppy/viewtopic.php?t=97623]Multiple package installer/remover.[/url]
[url=http://www.murga-linux.com/puppy/viewtopic.php?t=97623]Multiple package installer/remover.[/url]
- Subito Piano
- Posts: 731
- Joined: Mon 28 May 2007, 03:12
- Location: UPSTATE New York
- Contact:
Rednotebook
Hi! Excellent work but rednotebook will not function as posted here. Launching in terminal gives
...although rednotebook does work in tahrpup 6.0.2. I did install the pet package python-webkit_1.1.8, but that dd not help.
Not sure where the problem lies....???
[EDIT] I downloaded and ran TahrPup and installed rednotebook -- it ran fine. Then i downloaded the LxPup sfs fie and loaded it "on the fly," then ran the lxpup pet as directed. It restarted the wm automatically, then rednotebook would not start. Terminal gives the following output:
Similar issues in the LxPup Slacko:
...but i can't find the python YAML package thru the package manager.
Code: Select all
Webkit was not found. It can be found in a package with the name python-webkit or pywebkitgtk
Not sure where the problem lies....???
[EDIT] I downloaded and ran TahrPup and installed rednotebook -- it ran fine. Then i downloaded the LxPup sfs fie and loaded it "on the fly," then ran the lxpup pet as directed. It restarted the wm automatically, then rednotebook would not start. Terminal gives the following output:
Code: Select all
root# rednotebook
INFO chardet not found. 'utf-8' encoding will be assumed
INFO Writing log to file "/root/.rednotebook/rednotebook.log"
INFO MathJax location: http://cdn.mathjax.org/mathjax/latest/MathJax.js
INFO chardet not found. 'utf-8' encoding will be assumed
INFO Running in portable mode: False
INFO First Start: False
INFO RedNotebook version: 1.4.0
INFO System info: machine: i686, platform: Linux-3.14.20-i686-athlon-with-glibc2.4, processor: athlon, python_version: 2.7.6, release: 3.14.20, system: Linux, GTK version: (2, 24, 23), PyGTK version: (2, 24, 0), Yaml version: 3.10
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GProxyDrive'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: g_type_add_interface_dynamic: assertion 'G_TYPE_IS_INSTANTIATABLE (instance_type)' failed
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GProxyMount'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GProxyShadowMount'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GProxyVolume'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GProxyVolumeMonitor'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GProxyVolumeMonitorUDisks2'.
self.builder.add_from_file(self.gladefile)
(rednotebook:1916): GLib-GIO-WARNING **: Tried to register an extension of the type (null) to extension point gio-native-volume-monitor. Expected type is GNativeVolumeMonitor.
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GDaemonVfs'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GDaemonVolumeMonitor'.
self.builder.add_from_file(self.gladefile)
(rednotebook:1916): GLib-GIO-WARNING **: Tried to register an extension of the type (null) to extension point gio-volume-monitor. Expected type is GVolumeMonitor.
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: cannot add interface type 'GLoadableIcon' to type 'GVfsIcon', since type 'GVfsIcon' already conforms to interface
self.builder.add_from_file(self.gladefile)
(rednotebook:1916): GLib-GIO-WARNING **: Tried to register an extension of the type (null) to extension point gio-vfs. Expected type is GVfs.
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GVfsUriMapper'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GVfsUriMapperSmb'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GVfsUriMapperHttp'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'GVfsUriMapperAfp'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'PupClientMonitor'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'PupClientDevice'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'PupVolumeMonitor'.
self.builder.add_from_file(self.gladefile)
(rednotebook:1916): GLib-GIO-WARNING **: Tried to register an extension of the type (null) to extension point gio-volume-monitor. Expected type is GVolumeMonitor.
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'PupClientVolume'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'PupMount'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: Two different plugins tried to register 'PupClientDrive'.
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: invalid cast from 'GDaemonVfs' to '<invalid>'
self.builder.add_from_file(self.gladefile)
Error creating proxy: Error calling StartServiceByName for org.gtk.Private.UDisks2VolumeMonitor: GDBus.Error:org.freedesktop.DBus.Error.Spawn.ChildExited: Launch helper exited with unknown return code 127 (g-dbus-error-quark, 25)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: g_object_new: assertion 'G_TYPE_IS_OBJECT (object_type)' failed
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: invalid (NULL) pointer instance
self.builder.add_from_file(self.gladefile)
/usr/share/rednotebook/rednotebook/gui/main_window.py:63: Warning: g_signal_connect_data: assertion 'G_TYPE_CHECK_INSTANCE (instance)' failed
self.builder.add_from_file(self.gladefile)
Segmentation fault
Code: Select all
# rednotebook
/usr/bin/python: /lib/libcrypto.so.0.9.8: no version information available (required by /usr/bin/python)
/usr/bin/python: /lib/libssl.so.0.9.8: no version information available (required by /usr/bin/python)
** (process:24713): WARNING **: Trying to register gtype 'GMountMountFlags' as enum when in fact it is of type 'GFlags'
** (process:24713): WARNING **: Trying to register gtype 'GDriveStartFlags' as enum when in fact it is of type 'GFlags'
** (process:24713): WARNING **: Trying to register gtype 'GSocketMsgFlags' as enum when in fact it is of type 'GFlags'
INFO chardet not found. 'utf-8' encoding will be assumed
2015-02-16 19:43:59,817 INFO Writing log to file "/root/.rednotebook/rednotebook.log"
2015-02-16 19:43:59,818 INFO System encoding: UTF-8
2015-02-16 19:43:59,818 INFO Language code: en_US
2015-02-16 19:43:59,829 ERROR PyYAML not found. Please install python-yaml or PyYAML
Re: Rednotebook
Hi - this appears to be a very large (>100MB) and complicated application which installs all sorts of dependencies and libraries. I'm not even really clear what the application does (or why it needs to be so large).Subito Piano wrote:but rednotebook will not function
It doesn't seem to have been supported on Slackware since version 13.37 - see http://pkgs.org/search/rednotebook - LxPup current is based on Slackware 14.1 components.
If it works on TahrPup then it may be best to keep running it there.....
Sorry can't be more help on this one - I think it just isn't compatible with LxPup.
Cheers
peebee
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
- Subito Piano
- Posts: 731
- Joined: Mon 28 May 2007, 03:12
- Location: UPSTATE New York
- Contact:
Youtube review
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
-
- Posts: 14
- Joined: Fri 20 Feb 2015, 15:21
yes,me too! so far, I like LxPup 15.02 non-Pae) very much....I like the lxde (?) window manager versus the jwrmc(?) because it is easier for this windoze refugee and especially, it works with Opencpn navigation program.
I have used on 3 laptops from usb stick: HP G60, HP Dv1000 and a Dell D420
The only real pest has been the D420's Broadcom 4311 wireless card but I eventually found the tip to blacklist "wl" and that works!!
(...tahrpup 6.0.02 is excellent too (and no issue with B4311) except I could not get OpenCPN to display properly on it. I think it must be due to Opencpn's wxgtk dependencies ...)
I have used on 3 laptops from usb stick: HP G60, HP Dv1000 and a Dell D420
The only real pest has been the D420's Broadcom 4311 wireless card but I eventually found the tip to blacklist "wl" and that works!!
(...tahrpup 6.0.02 is excellent too (and no issue with B4311) except I could not get OpenCPN to display properly on it. I think it must be due to Opencpn's wxgtk dependencies ...)
-
- Posts: 11
- Joined: Fri 27 Feb 2015, 19:15
wlan0 not seen after initial save/reboot - LxPupTahr 15.02.1
I posted this issue in the newbie help forum and it was recommended that I post it here as well. It is copied and pasted so it may require edits for clarification. PM me if this is the case. Thanks:
wlan0 not seen after initial save/reboot - LxPupTahr 15.02.1
I tried the vanilla JWM TahrPup, even though I can't tolerate that desktop, and had a similar problem, but "ifconfig wlan0 up" in the terminal fixed it right away.
Not the case here, I'm getting "ifconfig: SIOCGIFFLAGS: no such device" and prior to the first reboot when setting up the save file everything was working fine.
I tried several Puppy variants and this is the one I want to stick with for being up to date, complete (distros like X-Slacko lacked things like Xsane and Peasyscan) and having an agreeable desktop environment, but I need wifi to work.
I'm setting it up on an Acer Aspire One 532h-2588 which according to system info utilities has an Atheros AR5B95 Wireless Network Adapter, but this install (via unetbootin) is on a USB stick* and I intend it as a portable OS to use on multiple computers wherever I happen to be, so I can't constantly be fussing with wifi issues.
I have been using Linux Mint for nearly a couple years now, but I am new to Puppy. Any clues? I have done the initial set up several times, deleted the save file and started over but this keeps happening. It really seems like a major bug. Also, no access to a wired network, so hopefully the solution is through the terminal.
*The USB stick is FAT32, one single 16GB partition. It was freshly formatted prior to the install, but not upon deletion and rebuild of save file.
There is a folder called "Keys" on it containing my keepassx database and key file for access, in addition to the Puppy install. This must be accessible from other booted OSes as well as Puppy as it stores my logins/passwords.
The install uses the recommended .2fs file with heavy encryption and is located on the top level of the partition with the other Puppy OS files.
wlan0 not seen after initial save/reboot - LxPupTahr 15.02.1
I tried the vanilla JWM TahrPup, even though I can't tolerate that desktop, and had a similar problem, but "ifconfig wlan0 up" in the terminal fixed it right away.
Not the case here, I'm getting "ifconfig: SIOCGIFFLAGS: no such device" and prior to the first reboot when setting up the save file everything was working fine.
I tried several Puppy variants and this is the one I want to stick with for being up to date, complete (distros like X-Slacko lacked things like Xsane and Peasyscan) and having an agreeable desktop environment, but I need wifi to work.
I'm setting it up on an Acer Aspire One 532h-2588 which according to system info utilities has an Atheros AR5B95 Wireless Network Adapter, but this install (via unetbootin) is on a USB stick* and I intend it as a portable OS to use on multiple computers wherever I happen to be, so I can't constantly be fussing with wifi issues.
I have been using Linux Mint for nearly a couple years now, but I am new to Puppy. Any clues? I have done the initial set up several times, deleted the save file and started over but this keeps happening. It really seems like a major bug. Also, no access to a wired network, so hopefully the solution is through the terminal.
*The USB stick is FAT32, one single 16GB partition. It was freshly formatted prior to the install, but not upon deletion and rebuild of save file.
There is a folder called "Keys" on it containing my keepassx database and key file for access, in addition to the Puppy install. This must be accessible from other booted OSes as well as Puppy as it stores my logins/passwords.
The install uses the recommended .2fs file with heavy encryption and is located on the top level of the partition with the other Puppy OS files.
- Subito Piano
- Posts: 731
- Joined: Mon 28 May 2007, 03:12
- Location: UPSTATE New York
- Contact:
Re: wlan0 not seen after initial save/reboot - LxPupTahr 15.02.1
Hi rawmilk905rawmilk905 wrote:I posted this issue in the newbie help forum and it was recommended that I post it here as well. It is copied and pasted so it may require edits for clarification. PM me if this is the case. Thanks:
wlan0 not seen after initial save/reboot - LxPupTahr 15.02.1
I tried the vanilla JWM TahrPup, even though I can't tolerate that desktop, and had a similar problem, but "ifconfig wlan0 up" in the terminal fixed it right away.
Not the case here, I'm getting "ifconfig: SIOCGIFFLAGS: no such device" and prior to the first reboot when setting up the save file everything was working fine.
I tried several Puppy variants and this is the one I want to stick with for being up to date, complete (distros like X-Slacko lacked things like Xsane and Peasyscan) and having an agreeable desktop environment, but I need wifi to work.
I'm setting it up on an Acer Aspire One 532h-2588 which according to system info utilities has an Atheros AR5B95 Wireless Network Adapter, but this install (via unetbootin) is on a USB stick* and I intend it as a portable OS to use on multiple computers wherever I happen to be, so I can't constantly be fussing with wifi issues.
I have been using Linux Mint for nearly a couple years now, but I am new to Puppy. Any clues? I have done the initial set up several times, deleted the save file and started over but this keeps happening. It really seems like a major bug. Also, no access to a wired network, so hopefully the solution is through the terminal.
*The USB stick is FAT32, one single 16GB partition. It was freshly formatted prior to the install, but not upon deletion and rebuild of save file.
There is a folder called "Keys" on it containing my keepassx database and key file for access, in addition to the Puppy install. This must be accessible from other booted OSes as well as Puppy as it stores my logins/passwords.
The install uses the recommended .2fs file with heavy encryption and is located on the top level of the partition with the other Puppy OS files.
Please try blacklisting the wl driver as that is present in LxPupTahr and is known to sometimes claim wifi devices erroneously.
After a first reboot, go:
Menu -> System -> System -> Boot Manager -> Modules -> Blacklist module
and move wl into the right hand pane
then reboot.
Cheers
peebee
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
-
- Posts: 11
- Joined: Fri 27 Feb 2015, 19:15
Re: wlan0 not seen after initial save/reboot - LxPupTahr 15.02.1
This did it , thank you!peebee wrote: Hi rawmilk905
Please try blacklisting the wl driver as that is present in LxPupTahr and is known to sometimes claim wifi devices erroneously.
After a first reboot, go:
Menu -> System -> System -> Boot Manager -> Modules -> Blacklist module
and move wl into the right hand pane
then reboot.
Cheers
peebee
New look?
I am considering a new look for LxPup at the next release....
The icon set is called flat-remix
The OpenBox theme is from Windows8OB by David Andrew
Please send any comments by PM so as not to clog up the thread.
Thanks
peebee
The icon set is called flat-remix
The OpenBox theme is from Windows8OB by David Andrew
Please send any comments by PM so as not to clog up the thread.
Thanks
peebee
- Attachments
-
- Screenshot.png
- (100.88 KiB) Downloaded 786 times
-
- flat-remix-icons.png
- (48.91 KiB) Downloaded 715 times
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
LxPupVivid
Thanks to the efforts of 666philb, LxPupVivid should be available soon.......
- Attachments
-
- capture4365.png
- (94.45 KiB) Downloaded 726 times
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
- clasico3124
- Posts: 15
- Joined: Sat 21 Mar 2015, 17:37
skype for lxpup tahr
hola,
tengo problemas con la llamada en skype no se escucha a la otra persona y la otra persona tampoco me escucha
uso puppy tahrpup con escritorio lxde
hello,
i have problem with skype call i dont lisen other person and the other dont lisent to me
i am use tahrpup with lxde
tengo problemas con la llamada en skype no se escucha a la otra persona y la otra persona tampoco me escucha
uso puppy tahrpup con escritorio lxde
hello,
i have problem with skype call i dont lisen other person and the other dont lisent to me
i am use tahrpup with lxde
Re: skype for lxpup tahr
Please use:clasico3124 wrote:hello,
i have problem with skype call i dont lisen other person and the other dont lisent to me
i am use tahrpup with lxde
Menu -> Setup -> ALSA Sound Wizard
to adjust your sound
and
Menu -> Multimedia -> Pavrecord
to test settings
Then try Skype again when you have sound configured correctly.
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
- clasico3124
- Posts: 15
- Joined: Sat 21 Mar 2015, 17:37
mixxx sound
hello,
thanks for help me with skype, now work all ok with skype call.
i have a new problem, with mixxx dont leave other app sound
i want speak with other person in skype, and both of us go air with mixxx
but mixxx doesnt premition other app sound
why only one app sound at the time
thanks for help me with skype, now work all ok with skype call.
i have a new problem, with mixxx dont leave other app sound
i want speak with other person in skype, and both of us go air with mixxx
but mixxx doesnt premition other app sound
why only one app sound at the time
LxPup-15.03
LxPup-15.03 is available to download from:
http://lx-pup.weebly.com/slacko60.html
Slackware-14.1 (Slacko6-Beta2) flavour with no-pae k3.4.94 and pae k3.17.7 versions
Main change is the new "look" - new default background, flat-remix iconset, Windows8OB window decoration, xfce-dawn gtk2 widgets
ppm and pup-sys-info also updated
(if you want to revert to a close approximation of the previous "look" then use Menu -> Desktop -> Change appearance and select:
Windows - Onyx
Theme - Nodoka-Aqua
Icons - Elementary
Background - vladstudio-windypress)
Note: updating an existing savefile will likely need some desktop reconfiguration after 1st boot - particularly an iconset will need to be selected and a windows manager restart done. This is because the box iconset is no longer included.
Cheers
peebee
http://lx-pup.weebly.com/slacko60.html
Slackware-14.1 (Slacko6-Beta2) flavour with no-pae k3.4.94 and pae k3.17.7 versions
Main change is the new "look" - new default background, flat-remix iconset, Windows8OB window decoration, xfce-dawn gtk2 widgets
ppm and pup-sys-info also updated
(if you want to revert to a close approximation of the previous "look" then use Menu -> Desktop -> Change appearance and select:
Windows - Onyx
Theme - Nodoka-Aqua
Icons - Elementary
Background - vladstudio-windypress)
Note: updating an existing savefile will likely need some desktop reconfiguration after 1st boot - particularly an iconset will need to be selected and a windows manager restart done. This is because the box iconset is no longer included.
Cheers
peebee
- Attachments
-
- Screenshot.png
- (95.61 KiB) Downloaded 2524 times
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
LxPupTahr-15.03
LxPupTahr has also now been updated to version 15.03.
See http://lx-pup.weebly.com/upup-tahr.html for download.
TahrPup updates to 22-Mar-2015 16:09 are included.
Box icons are no longer included.
The Puppy update process does not support LxPup fully, so if you are updating a previous install of LxPup you will need to do some manual tweaking after the 1st boot.
In particular you should:
- select the new iconset (flat-remix): Menu -> Desktop -> Desktop appearance -> Icons
- delete the optional top-panel if you have activated it and then re-activate it:
Menu -> Desktop -> Desktop appearance -> Options -> Top panel
You may also need to change the background and the GTK2 widget theme depending on how many changes you have made to these features in the past.
Cheers
peebee
See http://lx-pup.weebly.com/upup-tahr.html for download.
TahrPup updates to 22-Mar-2015 16:09 are included.
Box icons are no longer included.
The Puppy update process does not support LxPup fully, so if you are updating a previous install of LxPup you will need to do some manual tweaking after the 1st boot.
In particular you should:
- select the new iconset (flat-remix): Menu -> Desktop -> Desktop appearance -> Icons
- delete the optional top-panel if you have activated it and then re-activate it:
Menu -> Desktop -> Desktop appearance -> Options -> Top panel
You may also need to change the background and the GTK2 widget theme depending on how many changes you have made to these features in the past.
Cheers
peebee
- Attachments
-
- capture27596.png
- (131.41 KiB) Downloaded 2523 times
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64