Slacko Puppy version 5.5 - Unable to Connect
Slacko Puppy version 5.5 - Unable to Connect
I get the error:
Unable to connect
Firefox can't establish a connection to the server at www.google.com.au.
The error comes up almost instantly compared to the slow page loading I normally get on a 512k broadband. When I click retry a couple of times the page eventually loads.
My system has no problems under WinXP SP3.
Any advice?
Unable to connect
Firefox can't establish a connection to the server at www.google.com.au.
The error comes up almost instantly compared to the slow page loading I normally get on a 512k broadband. When I click retry a couple of times the page eventually loads.
My system has no problems under WinXP SP3.
Any advice?
I am connected with an ethernet cable although other devices are using wifi. I didn't set anything up, it just worked out of the box.
Modem / Router: Netcomm NB5 / Linksys WRTP54G
Lighthouse system info: https://docs.google.com/file/d/0B0YmifA ... sp=sharing
I noted a couple of errors.
bootsysinit.log
ERROR: could not insert 'acpi_cpufreq': Input/output error
Starting HAL daemon: /usr/sbin/hald --daemon=yes
pcd[3825]: eth0: executing `/usr/libexec/dhcpcd-run-hooks', reason CARRIER
(Maybe I am running the wrong version of slacko for my hardware.)
dhcpcp.log
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
dhcpcd[3825]: eth0: reading lease `/var/db/dhcpcd-eth0.lease'
(I don't want to upload my IP address.)
Modem / Router: Netcomm NB5 / Linksys WRTP54G
Lighthouse system info: https://docs.google.com/file/d/0B0YmifA ... sp=sharing
I noted a couple of errors.
bootsysinit.log
ERROR: could not insert 'acpi_cpufreq': Input/output error
Starting HAL daemon: /usr/sbin/hald --daemon=yes
pcd[3825]: eth0: executing `/usr/libexec/dhcpcd-run-hooks', reason CARRIER
(Maybe I am running the wrong version of slacko for my hardware.)
dhcpcp.log
Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
dhcpcd[3825]: eth0: reading lease `/var/db/dhcpcd-eth0.lease'
(I don't want to upload my IP address.)
Hi flywire
Had a look at your sys-info report - did you defrag your ntfs partition b4 using puppy? If not you should.
Another thought is with all the pets installed - save-file space is a bit low, try expanding it, or use sfs’s as you did with Office.
Better still - you’ve got loads of hdd space - after defragging, use gparted to provide a couple of ext2 partitions, one for puppy(‘ys) of choice and another for files.
I would also suggest a modest swap partition of approx. 512mb to 1gig.
With the above done. your ram and processor setup should allow any puppy you care to use, to absolutely fly.
HTH - best regards - Ray
Had a look at your sys-info report - did you defrag your ntfs partition b4 using puppy? If not you should.
Another thought is with all the pets installed - save-file space is a bit low, try expanding it, or use sfs’s as you did with Office.
Better still - you’ve got loads of hdd space - after defragging, use gparted to provide a couple of ext2 partitions, one for puppy(‘ys) of choice and another for files.
I would also suggest a modest swap partition of approx. 512mb to 1gig.
With the above done. your ram and processor setup should allow any puppy you care to use, to absolutely fly.
HTH - best regards - Ray
[b]Asus[/b] 701SD. 2gig ram. 8gb SSD. [b]IBM A21m[/b] laptop. 192mb ram. PIII Coppermine proc. [b]X60[/b] T2400 1.8Ghz proc. 2gig ram. 80gb hdd. [b]T41[/b] Pentium M 1400Mhz. 512mb ram.
I appreciate you comments Ray but with respect, Puppy seems fine but there is an error in the browser re connecting to the net. It is so bad now that it is not worth running because it takes so many clicks to bring up a page. (I'm on WinXP SP3 now.)
How do I work through the process of what happens from booting Slacko to bringing up a page? Probably just a simple setting or maybe a file has run out of space.
I did do a defrag before I started and the log file should show that I increased the size of my pup_save.2fs by 50%. The whole configuration thing is not clear to me - I don't even recall being asked to configure anything.
Still, my preference is to save files where they are accessible irrespective of the operating system rather than on ext2. Can I mount the pup_save.2fs as a drive in WinXP? Seems like an easy way of saving my files.
How do I work through the process of what happens from booting Slacko to bringing up a page? Probably just a simple setting or maybe a file has run out of space.
I did do a defrag before I started and the log file should show that I increased the size of my pup_save.2fs by 50%. The whole configuration thing is not clear to me - I don't even recall being asked to configure anything.
Still, my preference is to save files where they are accessible irrespective of the operating system rather than on ext2. Can I mount the pup_save.2fs as a drive in WinXP? Seems like an easy way of saving my files.
Your savefile may have become corrupted, especially if you use .2fs rather than .3fs
e2fsck can help restore it
http://puppylinux.org/wikka/e2fsck
Boot Puppy without loading the Savefile, so it isn't mounted
DO NOT USE ON MOUNTED FILESYSTEM
I like to use these options-
-y Assume "yes" to all questions
-c Check for bad blocks and add them to the badblock list
-v Be verbose
for example-
e2fsck /mnt/home/lslackosave-flywirel.2fs -ycv
e2fsck can help restore it
http://puppylinux.org/wikka/e2fsck
Boot Puppy without loading the Savefile, so it isn't mounted
DO NOT USE ON MOUNTED FILESYSTEM
I like to use these options-
-y Assume "yes" to all questions
-c Check for bad blocks and add them to the badblock list
-v Be verbose
for example-
e2fsck /mnt/home/lslackosave-flywirel.2fs -ycv
Hi flywire,
in order to track down the reason for this issue I would recommend that you boot your PC from a CD containing the Slacko 55 iso (typing "puppy pfix=ram" at the first boot prompt).
This will help confirm whether or not the condition is caused by some other factor of the installation process.
If you get different symptoms then we can recommend some other steps as a means of re-installing. If you get the same symptoms that would indicate a bad download or some incompatibilty between Slacko55 and your hardware or router. If that is the case then you may well find a different puppy that does the job well. (As a trial I would recommend Pemasu's "Upup Raring 3.9.9.2" which seems quite stable on my hardware. Link here:http://murga-linux.com/puppy/viewtopic.php?t=87374)
Even if you don't want to run a different puppy at least it may contribute to our understanding of what works and what doesn't.
Bear in mind that puppy is a cutdown operating system and the devs don't have access to all hardware so some trial and error may be necessary. Hopefully we can help you get a good puppy running on your machine.
in order to track down the reason for this issue I would recommend that you boot your PC from a CD containing the Slacko 55 iso (typing "puppy pfix=ram" at the first boot prompt).
This will help confirm whether or not the condition is caused by some other factor of the installation process.
If you get different symptoms then we can recommend some other steps as a means of re-installing. If you get the same symptoms that would indicate a bad download or some incompatibilty between Slacko55 and your hardware or router. If that is the case then you may well find a different puppy that does the job well. (As a trial I would recommend Pemasu's "Upup Raring 3.9.9.2" which seems quite stable on my hardware. Link here:http://murga-linux.com/puppy/viewtopic.php?t=87374)
Even if you don't want to run a different puppy at least it may contribute to our understanding of what works and what doesn't.
Bear in mind that puppy is a cutdown operating system and the devs don't have access to all hardware so some trial and error may be necessary. Hopefully we can help you get a good puppy running on your machine.
hi flywire,
if the problems persist in the newer slacko it's worth trying a different puppy to see if that has the same problems ..... try a precise..
http://ftp.nluug.nl/ibiblio/distributio ... -retro.iso
or
upup precise http://www.murga-linux.com/puppy/viewtopic.php?t=84944
if the problems persist in the newer slacko it's worth trying a different puppy to see if that has the same problems ..... try a precise..
http://ftp.nluug.nl/ibiblio/distributio ... -retro.iso
or
upup precise http://www.murga-linux.com/puppy/viewtopic.php?t=84944
Bionicpup64 built with bionic beaver packages http://murga-linux.com/puppy/viewtopic.php?t=114311
Xenialpup64, built with xenial xerus packages http://murga-linux.com/puppy/viewtopic.php?t=107331
Xenialpup64, built with xenial xerus packages http://murga-linux.com/puppy/viewtopic.php?t=107331
Slacko Puppy version 5.6 - Unable to Connect
I downloaded the Slacko 5.6 Non-PAE and have been running it for over a week in RAM. (It detects the old 5.5 install on my hard drive and allows any letter to be selected to run in RAM.)
I still get the unable to connect message frequently and after retrying a few times the page comes up.
(BTW The first version that I tried was precise which is why I went to Slacko.)
I still get the unable to connect message frequently and after retrying a few times the page comes up.
(BTW The first version that I tried was precise which is why I went to Slacko.)
Ok, I gather that hardware is good, clean contacts and in perfect working order just so we can eliminate that.
Also, just be sure you got a good download by checking the md5sum (checksum) available from the repo where you downloaded the iso.
We need to know exactly what device ID your interface has, so run this:
Post the output please. If you know what your adapter is (usually it's easy to tell in the output, will say "Ethernet adapter" or similar) just post that part, or even just look for the HEX code that identifies your adapter, in the form of [vendorID:deviceID]
example: [10ec:8136]
Do a fresh boot and and post the output of dmesg. Probably the best way to do that is to run this:
This will make a file called my-dmesg.txt.gz which is a gzipped archive and can be uploaded to the forum. Upload it.
Without these hard facts it's difficult to offer any diagnosis.
What we are looking for is that your driver gets loaded and is stable. If it is then the problem is elsewhere. We'll look at that when we can confirm that there is either an issue or not with the kernel loading your particular module.
Also, just be sure you got a good download by checking the md5sum (checksum) available from the repo where you downloaded the iso.
We need to know exactly what device ID your interface has, so run this:
Code: Select all
lspci -nn
example: [10ec:8136]
Do a fresh boot and and post the output of dmesg. Probably the best way to do that is to run this:
Code: Select all
dmesg > my-dmesg.txt
gzip my-demsg.txt
Without these hard facts it's difficult to offer any diagnosis.
What we are looking for is that your driver gets loaded and is stable. If it is then the problem is elsewhere. We'll look at that when we can confirm that there is either an issue or not with the kernel loading your particular module.
Puppy Linux Blog - contact me for access
Please note that I have downloaded 3 versions of Slacko and all have the same problem.
00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2)
Files uploaded.
I ran the console from the icon on the desktop. Can I cut and paste to/from the console?
00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2)
Files uploaded.
I ran the console from the icon on the desktop. Can I cut and paste to/from the console?
- Attachments
-
- my-dmesg.txt.gz
- (14.12 KiB) Downloaded 439 times
Ok, I'll take a look. I had an nvidia board which I was developing in but it died so this seems a little unusual to be unsupported (or flakey support to be more correct).. maybe the hardware is crap? I say that because my board was only 3 years old and was aging badly, sound died, one of the RAM slots died, overheating, especially in Windows... wasn't worth keeping.
LATER:
Hmmm.. definitely a weird problem..
Please check your cables as the pattern is rather erratic. Not saying it is cable related but it is very weird.
Hightlight text and middle click, or if no middle button/scroll wheel click left and right buttons simultaneously.flywire wrote:Can I cut and paste to/from the console?
LATER:
Hmmm.. definitely a weird problem..
Code: Select all
[ 545.956313] forcedeth 0000:00:07.0: eth0: link down
[ 547.795831] forcedeth 0000:00:07.0: eth0: link up
[ 567.978180] forcedeth 0000:00:07.0: eth0: link down
[ 569.757710] forcedeth 0000:00:07.0: eth0: link up
[ 589.569048] forcedeth 0000:00:07.0: eth0: link down
[ 591.401016] forcedeth 0000:00:07.0: eth0: link up
[ 607.050450] forcedeth 0000:00:07.0: eth0: link down
[ 608.832934] forcedeth 0000:00:07.0: eth0: link up
[ 630.160157] forcedeth 0000:00:07.0: eth0: link down
[ 631.930837] forcedeth 0000:00:07.0: eth0: link up
[ 646.494732] forcedeth 0000:00:07.0: eth0: link down
[ 648.335874] forcedeth 0000:00:07.0: eth0: link up
[ 673.732904] forcedeth 0000:00:07.0: eth0: link down
[ 675.518657] forcedeth 0000:00:07.0: eth0: link up
[ 759.587675] forcedeth 0000:00:07.0: eth0: link down
[ 761.378353] forcedeth 0000:00:07.0: eth0: link up
[ 791.709145] forcedeth 0000:00:07.0: eth0: link down
[ 793.474254] forcedeth 0000:00:07.0: eth0: link up
[ 800.861516] forcedeth 0000:00:07.0: eth0: link down
[ 802.680700] forcedeth 0000:00:07.0: eth0: link up
[ 910.439567] forcedeth 0000:00:07.0: eth0: link down
[ 912.284642] forcedeth 0000:00:07.0: eth0: link up
[ 914.158988] forcedeth 0000:00:07.0: eth0: link down
[ 915.943754] forcedeth 0000:00:07.0: eth0: link up
[ 927.720709] forcedeth 0000:00:07.0: eth0: link down
[ 929.564487] forcedeth 0000:00:07.0: eth0: link up
[ 940.073652] forcedeth 0000:00:07.0: eth0: link down
[ 941.863674] forcedeth 0000:00:07.0: eth0: link up
[ 948.127715] forcedeth 0000:00:07.0: eth0: link down
[ 949.916740] forcedeth 0000:00:07.0: eth0: link up
[ 1020.323734] forcedeth 0000:00:07.0: eth0: link down
[ 1021.884977] forcedeth 0000:00:07.0: eth0: link up
[ 1037.292195] forcedeth 0000:00:07.0: eth0: link down
[ 1039.084509] forcedeth 0000:00:07.0: eth0: link up
[ 1049.880478] forcedeth 0000:00:07.0: eth0: link down
[ 1051.666891] forcedeth 0000:00:07.0: eth0: link up
[ 1077.972467] forcedeth 0000:00:07.0: eth0: link down
[ 1079.751992] forcedeth 0000:00:07.0: eth0: link up
[ 1084.745300] forcedeth 0000:00:07.0: eth0: link down
[ 1086.593983] forcedeth 0000:00:07.0: eth0: link up
[ 1147.286828] forcedeth 0000:00:07.0: eth0: link down
- Attachments
-
- Screenshot_2013-09-12_12-15-37.png
- (4.87 KiB) Downloaded 773 times
Puppy Linux Blog - contact me for access
flywire,
You are not alone, some others have reported this since kernel 3.2.
Here is something to try.
At terminal type this.
Reboot and see what happens.
Ref
Good luck!
You are not alone, some others have reported this since kernel 3.2.
Here is something to try.
At terminal type this.
Code: Select all
echo "options forcedeth msi=0 msix=0" > /etc/modprobe.d/forcedeth.conf
Ref
Good luck!
Puppy Linux Blog - contact me for access
For what it's worth, no troubles here in Slacko 5.5 or 5.6..... using 5.5 right now.
Code: Select all
# lspci -nn
00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2)
Code: Select all
# uname -r
3.2.33-4g
#
From 5.6 .....
Have had no problems.
EDIT:
Mobo is about 1 yr old.
Code: Select all
# uname -r
3.4.52
#
Code: Select all
[ 16.324237] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 16.324398] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
[ 16.324406] forcedeth 0000:00:07.0: setting latency timer to 64
[ 16.847318] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:25:22:61:55:fc
[ 16.847323] forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
[ 16.847668] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.847915] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 16.848231] ACPI: PCI Interrupt Link [LMC9] enabled at IRQ 21
[ 16.848242] nvidia 0000:00:0d.0: setting latency timer to 64
[ 16.848247] vgaarb: device changed decodes: PCI:0000:00:0d.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 16.848466] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.37 Wed Mar 6 16:56:05 PST 2013
[ 17.222693] forcedeth 0000:00:07.0: irq 43 for MSI/MSI-X
[ 17.222735] forcedeth 0000:00:07.0: eth0: MSI enabled
[ 17.222991] forcedeth 0000:00:07.0: eth0: no link during initialization
[ 17.234440] forcedeth 0000:00:07.0: irq 43 for MSI/MSI-X
[ 17.234480] forcedeth 0000:00:07.0: eth0: MSI enabled
[ 17.234735] forcedeth 0000:00:07.0: eth0: no link during initialization
[ 17.734526] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.741448] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 18.420785] forcedeth 0000:00:07.0: eth0: link up
Mobo is about 1 yr old.
Apparently it is a BIOS problem and updating fixes it, I guess James yours already has the newer BIOS.James C wrote:Mobo is about 1 yr old.
RefP23 bios from EVGA fixed the ethernet bug
So, flywire, the real solution is to update the BIOS, however the above work around I supplied should work.
Puppy Linux Blog - contact me for access